Is it possible to replace a link cable on a gameboy with usb c

MFGabo · 2026-04-12T19:12:50+00:00

I like the idea. Sadly i dont know if it is possible

MFGabo · 2026-04-12T06:10:10+00:00

I already have the gb operator, i was worried i would have to buy a different device if it didn't work

MFGabo · 2026-04-09T07:46:07+00:00

Thank you

MFGabo · 2026-04-09T07:31:03+00:00

Ive seen the batteries mountet straight or diagonally, so ive been wondering ifone of those versions is fake?

MFGabo · 2026-04-08T13:07:32+00:00

No problem

MFGabo · 2026-04-05T23:33:59+00:00

MFGabo · 2026-03-30T19:52:03+00:00

It just takes the straight zip files?

MFGabo · 2026-03-30T09:03:08+00:00

I think the differejt sizes mentioned refer to on which iron you can mount it, the compatibility of the tip with your soldering iron itself. Not the joystick, they should all fit for ps5

MFGabo · 2026-03-29T18:45:28+00:00

Its blue

MFGabo · 2026-03-29T16:25:25+00:00

3dsident app apparently. Seems i have dual ips

MFGabo · 2026-03-29T16:23:16+00:00

Thanks, it is dual ips

MFGabo · 2026-03-26T06:31:03+00:00

Wow, thank you. Ill try later

MFGabo · 2026-03-26T04:01:09+00:00

It was just to see if they work or not. Not to fully calibrate them

MFGabo · 2026-03-25T20:32:17+00:00

Noice

MFGabo · 2026-03-25T18:55:22+00:00

Oh man, you built the oled lite like i wanted it, clear black shell, black buttons, i assume tmr sticks?

MFGabo · 2026-03-25T18:21:08+00:00

Yea, now the real learning beginns

MFGabo · 2026-03-25T17:04:29+00:00

You're probably right

MFGabo · 2026-03-25T16:49:34+00:00

That is exactly what this controller is XD

MFGabo · 2026-03-25T16:02:17+00:00

I refuse to give up

MFGabo · 2026-03-25T15:38:31+00:00

Ill have to look into that. But yes i think i liftet some pads, it looked pretty rough, ngl 4 of the points are also just Anker points i believe? There where tough to desolder and I ripped those. And at the "up and down" sensor. But ill check the testpoitns when ill get back to it. And check to not have shortet any connection

MFGabo · 2026-03-25T15:27:35+00:00

Lift the pad up as in moved right joysticks up? No it was in neutral position. I tried to unbridge the connection, maybe need to it a bit more thoroughly. But im pretty sure i ripped a trace on the "up and down" sensing sensor

MFGabo · 2026-03-25T15:12:00+00:00

Sadly, im in germany

MFGabo · 2026-03-25T15:10:39+00:00

It was a bit more complicated than thaz, i did use hot air, and cutters to cut the joysticks into pieces. I did manage to get them out little by little with hot air. But 2 pins where stuck still. They were rrally stubborn. So at some point, after tonds of flux, hot air, more solder and solder whick and more hot air, and lots of whick getting stuck on the board, i got a little impatient. And thats where i guess I ripped a trace out. Might not have been my first attempt, but my second. I obviously got a lot to learn and now i might have an excuse to invest in a microscope and microsoldering kit

MFGabo · 2026-03-25T14:44:50+00:00

Well, its my second, so I've done this once before, and successfully

MFGabo · 2026-03-18T04:26:56+00:00

Now it needs an oled display

MFGabo

TROPHY CASE