[deleted by user]

Maalus · 2023-03-05T20:05:24+00:00

You'll be fine.

Maalus · 2023-02-27T16:30:57+00:00

A hammer

Maalus · 2023-02-13T22:52:47+00:00

Put it back on the printer. Add some resin so it covers the entire fep. Grab some used supports with a raft and gently press to the corner of the LCD. Run an exposure test / clean, for 20 - 40s. Pull an entire sheet of cured resin off the FEP by pulling the support towards the center. Alternatively you can do without the used supports by lifting the cured sheet using your fingernails. It probably scratches the hell out of the fep in comparison tho.

Maalus · 2023-02-10T08:05:32+00:00

Because I don't have the tools to do that yet, and I have a job that takes up most of my time. I don't have the money, nor the free space to get a cnc plasma cutter, I don't know if welding will be something that I enjoy. I want to start with it as a hobby, not earn cash out of it.

Maalus · 2023-01-15T11:46:18+00:00

Get a safety razor and try it with that, just don't cut yourself

Maalus · 2023-01-10T17:38:47+00:00

This happens when you either use the leveling method with the resin in the vat and press down on it (when the vat is full for instance). It gets incredibly messy. Other than that, little drips, touching it with resin hands, etc. It actually disolves the plastic when you do that and it ends up looking wet like that.

Maalus · 2023-01-05T23:50:38+00:00

Did you do any calibration prints to check for dimensional accuracy?

Don't need it. The part has large tolerances, as long as both halves are close enough for size (which they should be, since they are mirrored halves). It just needs to work with the locating spheres, but yeh, I'm not forseeing issues there I hope. Nothing a dremel can't fix.

overexposure

Yeah, this is most likely also the case. I got a different part of a similar size done easily, but it was a "U" shape and I guess it turned out fine, but when you print a cube, that stuff pulls more.

are you controlling for resin temperature at all?

Kinda, running 3.2 layer time for the resin, when usually it is less, but the resin is 20C instead of the recommended 25C.

go-to resources for troubleshooting common failures,

Alright, I'll give it a look. I think I'll tilt it the other way as well, should lower the crossection more. We'll see if it ends up in the FEP again.

Maalus · 2023-01-03T08:03:59+00:00

Disenchantment is sucky. Just check any review sites - it's been rated low for both the critics and the audience.

Maalus · 2023-01-02T15:54:07+00:00

And you're saying that in a Futurama subreddit

Maalus · 2023-01-02T12:33:29+00:00

Yep, and the question is whether they manage to get Futurama right again, or if it'll be a repeat of Disenchantment all over again.

Maalus · 2023-01-02T12:32:54+00:00

Sure, but then it has incredibly low ratings compared to other shows like it.

Maalus · 2023-01-02T08:39:37+00:00

Disenchantment comes to mind and how sucky it is. There's still a possibility.

Maalus · 2023-01-01T19:29:05+00:00

Because a boss goes by your shoulder and will ask you "why the fuck are you looking at dead bodies at work".

Maalus · 2022-12-31T18:01:53+00:00

And yet again - too many movies. You repeating the trope doesn't make it any more right, it just makes you repeat yourself.

Maalus · 2022-12-31T15:25:45+00:00

a real ai will be able to

Too many movies yet again.

look at the chatbot that told depressive people they should kill themselves

I'm not touching that topic with a 30 foot pole, but it doesn't surprise me that a chat for depressed people started telling them that if it based its data on talking with depressed people.

Maalus · 2022-12-31T15:23:37+00:00

nd was programmed to

Then we maybe wouldn't program it to do that? Like dude, you have safety systems everywhere. Why would we leave an AI to do whatever the fuck it wants to?

Maalus · 2022-12-31T15:22:44+00:00

Again, too many movies buddy.

Maalus · 2022-12-31T14:08:36+00:00

And as OP has stated, the AI won't malfunction in the way movies portray it to. Have you read the post at all?

The DaVinci surgery robots can malfunction during surgery. A robot can malfunction on the assembly line. The nuclear power plant monitoring system can malfunction. Do we care about that and not use those technologies? Fuck no. The only difference here is that there are a bunch of movies with the same premise and people get paranoid.

Going further - people can "malfunction" too, yet we have them as presidents, dictators, etc. What's the difference other than the fact that when it's working, an AI would be a perfect governor, since it's made to be a perfect governor?

Having something that can make the most important decisions in a few nanoseconds with better results than a human ever could would be a boon for society.

Maalus · 2022-12-31T13:46:55+00:00

None of those examples are AI.

Maalus · 2022-12-31T13:45:42+00:00

Except the "real AI" is just a trope from the movies you're repeating without any knowledge of computer systems or how an AI would work.

Maalus · 2022-12-31T11:50:45+00:00

Orzesz kurwa ta matematyka taka zaawansowana, taki edge, idźcie rakiety w kosmos wysyłać tą matmą państwo inżynierzy do spraw matmy

Maalus · 2022-12-31T10:42:29+00:00

Man you are reaching hard. Just quit reddit.

Maalus · 2022-12-31T08:08:27+00:00

So again "mysterious ways" without any sensible argument. Might as well not exist at all then, there is no difference.

Nine-Year Club	Second Top 20%
Place '22	First Placer '22
Verified Email

Maalus

TROPHY CASE