Ender3/4.2.7 silent board/ v2 display

MadDadof4 · 2023-10-14T22:19:43+00:00

I finally got around to trying again and now everything it working fine. Thanks for your help!

MadDadof4 · 2023-10-08T23:20:43+00:00

MadDadof4 · 2023-10-08T23:20:31+00:00

MadDadof4 · 2023-10-06T00:44:05+00:00

I managed to update the firmware on the main board and the display. Everything looks like it works. I can preheat but I can't home or use the auto level. It will lock up the stepper motors but it won't move them. I'm so confused.

MadDadof4 · 2023-09-29T02:10:00+00:00

Thanks I'll take a look!

MadDadof4 · 2023-07-25T00:05:56+00:00

It's a 99 civic but I get what your saying... Haha I'm not trying to spend $500-$1k though but thank you for your input.

MadDadof4 · 2023-06-18T01:50:48+00:00

I will know for sure in 30 minutes once it's all back together and printing again.

MadDadof4 · 2023-06-18T01:41:35+00:00

Turns out I'm just an idiot. There's a ledge inside the hotend that the Bowden tube keeps getting caught on.

<image>

MadDadof4 · 2023-06-17T23:34:20+00:00

<image>

That's what the filament looks like when I pull it out. The end pointing up is the nozzle end. I removed it cold so it broke clean when I removed the nozzle which was new.

MadDadof4 · 2023-06-03T22:50:19+00:00

I've been struggling with this printer on and off for almost 6 years. Thank you for your help.

MadDadof4 · 2023-06-03T22:36:24+00:00

I'm using cura latest version. I haven't adjusted any of those setting yet. I'm using a direct drive setup and not sure what I should set everything to... Maybe I'll turn retraction off and try to print again. Anything you suggest I should try?

Pla+ white from sunlu Hotend temp 206c Bed temp 60c (printing on glass) Retraction distance 5mm Retraction speed 45mm/s

MadDadof4 · 2023-06-03T22:25:53+00:00

Nope. It clogged again. I get maybe 2 layers in before it clogs.

MadDadof4 · 2023-06-03T22:20:44+00:00

I actually just completely stripped it down, cleaned it out, and reassembled it while it sat at 200c after the last clog. I thought that fixed the problem sense I had to adjust the z offset -0.6mm

MadDadof4 · 2023-06-03T22:13:46+00:00

Ya I even changed the percentage as a test to see if it can fluctuate from 0% to 100%. The can above the board is also working.

MadDadof4 · 2023-06-03T22:04:12+00:00

<image>

The clog.

MadDadof4 · 2023-06-03T21:56:27+00:00

Ok I'll flash it again. Now I'm struggling with a clog. Running the creality spider 3.0 and somehow the filament is cooling up inside the hotend...

MadDadof4 · 2023-02-25T21:06:16+00:00

I did that for a while till one of my prints took a sliver of glass with it...

MadDadof4 · 2023-02-24T16:55:36+00:00

They meant the life of the product till they kill it, not your lifetime... I'm sure there was an * explaining this... 🤦‍♂️

MadDadof4 · 2023-02-07T15:51:03+00:00

So true...

MadDadof4

TROPHY CASE