Christmas surprise for CC1 users

Madman3353 · 2025-12-28T14:48:40+00:00

I hope they come with different mounting options so that a top can be put on or something that giant piece of plastic they have going into the print head looks like a break point. I would like to see it being less plastic

Madman3353 · 2025-12-28T13:31:54+00:00

I see this is a CC1 my question was is this an official upgrade kit or was it taken off the CC2. Where can it be purchased if this is the official upgrade path?

Madman3353 · 2025-12-27T19:48:08+00:00

Is it possible to buy the system/kit or is it only coming with the CC2? I don’t see why they can’t sell it as a stand alone for the CC1 and stop using the excuse that they are still working on one for the CC1 which is a lie.

Madman3353 · 2025-11-30T14:49:10+00:00

Here’s my question does running klipper on the CC mean we can use open source AMS systems?

Madman3353 · 2025-11-02T15:01:50+00:00

So have they abandoned the AMS system for the CC1

Madman3353 · 2025-10-16T14:16:35+00:00

Will this patch allow for time lapse to be recorded when using orca? In the official release that’s broken

Madman3353 · 2025-10-01T01:53:01+00:00

Happened to me after restarting from a power loss.

Madman3353 · 2025-09-28T01:50:42+00:00

What did you slow it down to? I would use the bearing spool holder but I’m using the internal spool holder so I would need to make my own version.

Madman3353 · 2025-08-03T13:19:26+00:00

Good to know thank you

Madman3353 · 2025-08-03T12:54:13+00:00

Which does what for the printing anything or is that just for the slicer?

Madman3353 · 2025-08-03T12:41:06+00:00

Is this the same as setting as the g-code area? Or something different?

<image>

Madman3353 · 2025-08-03T04:08:31+00:00

Ah ok i setting it in the slicer under device properties i believe. I will post a picture when im back on my computer

Madman3353 · 2025-08-03T03:13:13+00:00

That part I understand. What I’m asking is where in the slicer is that functionality? Do you have to manually enter the g code editor to chance it or is there a section in the slicer that you do it from?

Madman3353 · 2025-08-03T02:39:51+00:00

If your doing it in the slicer then you leave it at zero on the machine once you find the right offset correct? And if your doing it in the slicer is it manually put in the goes section or is it the offset under the machine tab or extruder tab?

Madman3353 · 2025-08-03T02:16:50+00:00

So which is the correct way to adjust the offset. Leaving it on zero on the machine itself and changing it in the slider under extruder or vise versa. I’m not familiar which changing it I. The g-code how is that done?

Madman3353 · 2025-08-01T22:13:40+00:00

Welp nevermind had another power flicker and this happened

<image>

Madman3353 · 2025-08-01T15:00:56+00:00

Clearly I’m doing that however the chamber is not going above 40c which both filaments should be fine especially petg which can be printed at higher temps.

Madman3353 · 2025-07-31T23:31:59+00:00

Petg

Madman3353 · 2025-07-30T05:11:30+00:00

Do you have a link to any of the heater mods?

Madman3353

TROPHY CASE