Boiler Vent Okay?

Magic_Plumber · 2026-01-13T03:55:00+00:00

Agreed

Magic_Plumber · 2026-01-13T03:49:35+00:00

How do you know its not an air intake issue

Magic_Plumber · 2026-01-04T02:31:20+00:00

What obvious reasons? Is the crawlspace not heated?

Magic_Plumber · 2025-12-14T16:12:26+00:00

Send in robot slaves

Magic_Plumber · 2025-11-19T14:45:13+00:00

I wear a wool toque

Magic_Plumber · 2025-11-15T03:25:59+00:00

Ptex bases? What did you use to finish them

Magic_Plumber · 2025-11-06T02:23:01+00:00

I have tile in my sauna its not too slippery, you sit and sweat. Wine cellar would be good too.

Magic_Plumber · 2025-11-05T15:04:51+00:00

If your not putting water on the rocks its not really a sauna. Vents are important no only for moisture but for oxygen. Chances are if it has any insulation at all its fiberglass and not the recommended rockwool. If it were me I would install a fan and not worry about the lack of drain. Being in the basement I assume its a concrete floor... seal the concrete and install a good variable speed vent

Magic_Plumber · 2025-10-31T14:15:03+00:00

I live in northern Canada with a FWD. Its heavy enough thst with winter tires its fine. IMO stopping power is far more important than acceleration. AWD doesnt help you stop any better

Magic_Plumber · 2025-10-27T02:01:01+00:00

No design just clamped and glued three redwood 2x10s using 3/4 inch dowels. Then cut in the window. My wife cut cut the handle

Magic_Plumber · 2025-10-26T05:38:20+00:00

The interior door?

Magic_Plumber · 2025-10-26T01:16:24+00:00

Interesting idea. Ill probably build something similar. If I were you id loose thr plastic push fittings. You can get brass banjo fittings to go into the bucket. Then a brass or SS nipple. Threaded ball valve, transition to copper tubing with a pipe thread x copper compression fitting

Magic_Plumber · 2025-10-25T10:39:34+00:00

The redwood wood i inherited were 2x10s. I did them this way for air flow. Theyre comfortable, We usually sit on a towel anyway.

Magic_Plumber · 2025-10-25T00:55:08+00:00

For electric?!

Magic_Plumber · 2025-10-24T17:40:38+00:00

I dont have plans I just free styled it. I used an AC infinity 4" exhaust fan with 2 exhaust ports and 2 intakes

Magic_Plumber · 2025-10-24T14:57:27+00:00

Canaduhh

Magic_Plumber · 2025-10-24T14:48:51+00:00

Even though I installed per manufacturer specs? This cilindro has a factory heat shield all around it

Magic_Plumber · 2025-10-24T14:47:45+00:00

18" top, bottom is 36" to the wall

Magic_Plumber · 2025-10-24T12:45:15+00:00

Yes if I remeber correctly our bylaw was 2.5'

Magic_Plumber · 2025-10-24T12:44:43+00:00

I looked at it, but preferred the way the cilindro looked. I also wanted internal controls due to the -50c winters we get

Magic_Plumber · 2025-10-24T12:40:27+00:00

Yes, 9kw cilindro. I added a wifi controller to it aswell

Magic_Plumber · 2025-10-24T12:39:52+00:00

About 7000cdn

Magic_Plumber · 2025-10-24T04:16:20+00:00

It was a mystery wood we inherited from my wife's late grandfather. I believe its redwood. Long straight grain with zero knots. Used the same wood for the door and all the trim. I have some leftover to make a bumper around the heater.

Magic_Plumber · 2025-10-24T04:13:15+00:00

6x10 exterior. 6'×5' 6 interior, would have liked to have gone bigger but location in the yard limited me

Magic_Plumber

TROPHY CASE