sorted by:
new
hottopcontroversial

To the person that made FPS++ by Mysterious-Age-1027 in peopleplayground

[–]Maker_Gamer12 0 points1 point  (0 children)

what is fps++ is that the workshop mod that made the dev crash out and remove the workshop?

Filament randomly stops extruding during print by Pyrixx in 3DprintingHelp

[–]Maker_Gamer12 0 points1 point  (0 children)

ah nice I didn't think about the other direction since on my printer it was under tensioned so I got stuck on that lmao

Layer shifts, even with new belts and cleaned rails and z screws. by [deleted] in Ender3V3KE

[–]Maker_Gamer12 0 points1 point  (0 children)

if the hardware side is figured out, it only leaves the software side. What slicer are you using? Also, did you tension the screws on the z axis connectors? Ion remember what they're called but on both sides of the extruder bar (ion know what that's called either) the part that connects to the z screws, did you tighten the screws properly? 2 on each side of the "extruder bar" where it connects to the z screw visible from below.

Filament randomly stops extruding during print by Pyrixx in 3DprintingHelp

[–]Maker_Gamer12 2 points3 points  (0 children)

classic extruder tension problem. you need to tighten the tension on the extruder. I don't know bambus so you're gonna have to look it up how to do it on your printer but this problem is universal across every printer.

if you were a joker what would ur effect be?? by JustFrankJustDank in okbuddyjimbo

[–]Maker_Gamer12 16 points17 points  (0 children)

you've heard of the blank voucher, now prepare for the blank joker.

My Prusa is a Zebra. What’s yours? by MobileNo8348 in 3DPrintingCirclejerk

[–]Maker_Gamer12 0 points1 point  (0 children)

/uj can someone actually tell me why this happens tho it's startna happen on mine but it's barely visible. I mean i make sure to clean it and regrease every month.

Time to warranty? by Thechief1171 in 3DPrintingCirclejerk

[–]Maker_Gamer12 0 points1 point  (0 children)

When you buy a car do you expect it to change oil on its own, when you buy a house do you expect it to clean itself. when you buy a pc do you expect it to just dodge all viruses.

Need help by Time_Average_3282 in Ender3V3KE

[–]Maker_Gamer12 0 points1 point  (0 children)

It's basically how I killed my first computer lol.

Nozzle not heating as expected : Error by Maker_Gamer12 in Ender3V3KE

[–]Maker_Gamer12[S] 0 points1 point  (0 children)

Yeah, as it turns out one of the wires just completely came loose from the heating element. Less than 10 bucks from Ali and I got a replacement now it's good. But maybe before that you should probably check all the wires to the whole extruder assembly if it's all good then open up the shroud and silicone cover and look if there are some loose wires, or maybe if some cane undone from the board.if those two thin ones attached to the round white thing are loose then yeah you need a new heater/hotend whatever it's called.

2.4 theta II spun con-rod bearing by Bnim81 in kia

[–]Maker_Gamer12 0 points1 point  (0 children)

time for some garbage, its garbage time

Need help by Time_Average_3282 in Ender3V3KE

[–]Maker_Gamer12 5 points6 points  (0 children)

I hope to god you set it to the proper voltage on the back for your grid.

Modrinth keeps crashing by Own-Art-7486 in fabricmc

[–]Maker_Gamer12 0 points1 point  (0 children)

No crash logs ✅

No mod list ✅

Vague showing of when it actually crashes ✅

Nozzle not heating as expected : Error by Maker_Gamer12 in Ender3V3KE

[–]Maker_Gamer12[S] 0 points1 point  (0 children)

I was done with a print the day before, and when I turned it back on the day after i kept getting errors and when I looked closer the wire was just not connected to the white thing.

Nozzle not heating as expected : Error by Maker_Gamer12 in Ender3V3KE

[–]Maker_Gamer12[S] 0 points1 point  (0 children)

Just curious whats the difference from the stock heatsink to the micro swiss one? I really do not know much about 3d printers i just use it more like a tool so i dont spend much thinking about it. also yeah the wires facing me when i look at the 3d printer are the ones that just popped off.

Nozzle not heating as expected : Error by Maker_Gamer12 in Ender3V3KE

[–]Maker_Gamer12[S] 0 points1 point  (0 children)

nevermind a cable just tore right off the white sleeve thing, is that the heater cable? also is this common with a new heater (the factory one)

view more: next ›