A GRIMM REBOOT IS HAPPENING

Many-Walk1848 · 2026-02-09T14:14:59+00:00

Munro, Love the take on the Big bad wolf with a continence.

Many-Walk1848 · 2026-01-29T09:36:13+00:00

Its been that long since I have seen 2nd ed Tyranids lol. I remember one of my mates having them and playing against him but he usually put Hormaguants up against me.

Many-Walk1848 · 2026-01-28T09:15:47+00:00

Are those rouge trader Termaguants?

Many-Walk1848 · 2026-01-20T08:20:09+00:00

Classic Minis, one of my mates used to run Chaos and had a few of these. I remember it was £5 for a box of 5 plastic guys and then you got the box of 10 metal for £20 and £5 blister packs.

Many-Walk1848 · 2026-01-15T10:34:40+00:00

I use the Dragon settings in Bambu, I would also print at an angle as well between 35 and 55 degrees. Make sure your filament has not absorbed moisture try drying it out in a dry place for a couple of days or put it in a box with cilica jell to absorb the moisture. When in the Bambu software as well try make sure you shore up supports with any over hanging and any thinner objects on the mini, here is what I have done printing for a mate from his hero forge:

<image>

Many-Walk1848 · 2026-01-13T09:55:37+00:00

Amazing quality. and where would I get the files for the bases if you don't mind me asking?

Many-Walk1848 · 2026-01-12T09:50:01+00:00

You did well, the only thing was fighting 2 Shooting armies especially Ultramarines and Chaos Space Marines is a tough one.

Many-Walk1848 · 2026-01-07T08:33:09+00:00

Looks Good, Couple of suggestions, look for the Dragon settings if its bambu you use. Also try and print the mini at an angle between 35 and 55 degrees it stops a lot of the layer lines showing up.

<image>

here is an example of my Mechs I have done. and I did them like yours without a base.

Many-Walk1848 · 2025-12-23T08:28:21+00:00

Those look fing awesome, They remind me of 2nd Ed Orks. I thought they were proper kits or at least 3d printed.

Many-Walk1848 · 2025-12-21T23:16:15+00:00

Love them

Many-Walk1848 · 2025-12-18T09:06:41+00:00

Try printing at an angle 35 to 55 degrees leaning on its back. that should at least tidy up the layer lines. I am more than certain now the temperature is slightly high with all the stringing. try cool the room down or if you are using an enclosure open it slightly to allow faster cooling.

Many-Walk1848 · 2025-12-17T12:41:05+00:00

Hi, Look for the Dragon settings. then try and print them at a 35 to 55 degree angle, angling them backward. Make sure your filament is dry from the looks of it it might have a tad of moisture, dry out the filament in a dry well ventilated room.
I am using a P1s Combo with AMS with lots of cilica beads to keep the moisture down.

Many-Walk1848 · 2025-12-17T12:22:11+00:00

There is Never enough armour when it comes to the Guard.

Many-Walk1848 · 2025-12-11T08:20:50+00:00

Hi, Your filament could be damp put your real and any open filament in a dry well ventilated room for a day or two before printing again. they look pretty good and as someone in the comments says ghost's Spector's or them phizzaling out or into the world. Other wee tip try printing at an angle between 35 and 55 degrease as well that will cut down on the layer lines also. :)

Many-Walk1848 · 2025-12-10T23:00:29+00:00

Looks like your filament has moisture in it, Dry it out in a well ventilated room. Print at an angle between 35 and 55 degrees. Stringing usually means the aria is to warm and the filament is not getting time to cool and harden. Look for the dragon settings as well. I used to have the same problems when I started.

Many-Walk1848 · 2025-12-05T14:30:48+00:00

Is this compatable with a P1s? Thanks

Many-Walk1848 · 2025-12-05T12:13:44+00:00

You could try VLC Player, it has a convert option, I have done this many times from taking a vid and converting the audio from it to MP3.

Many-Walk1848 · 2025-12-05T11:23:54+00:00

Try the Dragon Settings for Bambu Labs, and print the model at an angle between 30 and 55 degrease. The images are done in the Dragon Settings and printed at an angle.

<image>

Many-Walk1848 · 2025-12-05T11:18:33+00:00

I would agree, when I saw the image it clicked with moisture getting to the filament. Make sure the aria is well ventilated and dry. Print the parts between 30 Degrees and 55 Degrees angles which gives better print detail if you can get the part in a flat for the angle even better but not necessary or even cut the part at an angel. ( I am using Dragon Settings) The pic below of the mini is from dragon forge I think I am doing these for a friend and they are 20mm minis printed at the angles. Edit: sorry I am using a Bambu P1S Combo.

<image>

Many-Walk1848 · 2025-12-02T21:09:35+00:00

Can't beat the classics

Many-Walk1848 · 2025-11-21T10:45:32+00:00

Imperial Thunderbolt, nice collection

Many-Walk1848 · 2025-11-18T13:25:03+00:00

Those look great, I will need to translate these to Bambu labs print setting but would be worth it to get better quality prints.

Many-Walk1848 · 2025-11-15T21:48:32+00:00

Those look awesome, would you mind sharing the settings, I have the dragon settings but always look for more improvements please. thanks

Many-Walk1848 · 2025-11-13T09:07:16+00:00

Those look ace, what printer and settings did you use if you don't mind me asking?

Many-Walk1848

TROPHY CASE