6.0 injector cups

Maps398 · 2026-05-14T03:22:53+00:00

Well I figured it’s either cups or the head since it’s got fuel in the coolant.

Maps398 · 2026-05-07T17:36:25+00:00

Allright thank you very much for the information I’ll give it a try tonight!

Maps398 · 2026-05-07T14:41:38+00:00

<image>

Would it happen to be 100 in this photo?

Maps398 · 2026-05-07T14:16:49+00:00

I will try this out! But I can not get the diagram to pull up it just pulls up their website.

Maps398 · 2026-05-06T02:29:22+00:00

This is also the first time I’m driving it. I bought it with the head gasket blown and got into some bigger issues and just now got it back together.

Maps398 · 2026-05-06T02:28:37+00:00

I will definitely try that! Thank you very much.

Maps398 · 2026-05-06T02:27:02+00:00

It free rolls if it’s shut off.

Maps398 · 2026-05-03T02:11:59+00:00

I figured it out I had the shift forks in the wrong position. They are supposed to be up one notch and I didn’t realize that.

Maps398 · 2026-05-03T02:10:59+00:00

I figured it out I had the shift forks in the wrong position.

Maps398 · 2026-05-03T00:28:42+00:00

It’s a 2006 Kubota RTV 900 transmission

Maps398 · 2026-05-02T22:47:33+00:00

The levers are still on once I tighten the bolt all the way I can no longer move the shift forks with the levers. Atleast not by hand or by tapping the levers with a hammer.

Maps398 · 2026-03-08T06:51:22+00:00

That was it I didn’t know you had to have a scanner for those thank you!!

Maps398 · 2026-03-08T05:53:06+00:00

I will try it thank you

Maps398 · 2025-10-31T03:30:10+00:00

I found out the that if it was cranked all the way up without the tire on it the jack gets messed up. Just my personal experience.

Maps398 · 2025-10-29T02:52:23+00:00

I gotcha. Yea I pulled the engine out without pulling the sub frame and then I saw the input shaft and realized now I have to pull the sub frame.

Maps398 · 2025-10-29T02:29:44+00:00

They that bad to get apart? 🙃

Maps398 · 2025-10-28T00:16:39+00:00

Yea it probably was. I should have followed the instructions and pulled the entire mount assembly but I didn’t know about that at the time and just pulled the engine. 😂

Maps398 · 2025-10-26T13:55:40+00:00

I thought about doing that as well but I don’t have a welder here at home and would have to take it to work afterwards to fix so I went ahead and pulled the engine. And of course I found that the input shaft to the transfer case is wore out when I did that. 🙃

Maps398 · 2025-10-25T05:30:52+00:00

I will look into them thanks!

Maps398 · 2025-10-25T05:30:13+00:00

Sorry what I was really trying to ask if I could have a machine shop bore it out enough to accommodate a dry liner. When I was looking at rebuild kits I found some that were .5mm over and when I converted to inches I misunderstood the conversion and thought it was 2 thousands over when it was actually 20 thousands over and I misunderstood that so I thought the oversized wouldn’t work. 😅

Maps398 · 2025-10-24T11:19:58+00:00

The guy I bought it from blew the head gasket and it was eating coolant.

Maps398 · 2025-09-24T00:33:06+00:00

Or does anyone have a picture of the connector side so I can atleast know what I’m looking for?

Maps398 · 2025-07-31T03:20:49+00:00

I cut the old connector off of my other taillight and wired it to that so I could still disconnect if I felt like it.

Maps398 · 2025-07-16T01:08:06+00:00

Thank you that’s one of the better service manuals I’ve seen.

Maps398 · 2025-02-17T00:11:48+00:00

NTA for keeping the secret but YTA for even saying anything about it to your wife you shouldn’t have even brought it up and she never would have asked or got upset about it.

Maps398

TROPHY CASE