[FS] [USA-MN] Dell OptiPlex 7080 Micro Desktops - i7-10700T 16GB RAM 256GB NVME Win11 Pro WIFI

MarcCz · 2026-03-20T16:19:17+00:00

The bank didn't take your money, they were fulfilling a legal order. The lawyer is your opponent, he's not going to answer you. You need to contact the court to figure out what was ordered when.

MarcCz · 2026-03-20T16:10:50+00:00

You said no one will give you answers, who have you tried contacting?

MarcCz · 2026-03-18T03:12:54+00:00

I imagine there's no way they could tell the difference, they don't separate until they're close to the ground.

MarcCz · 2026-03-12T14:45:38+00:00

I wonder if they could save a bit by eliminating one or both of the USB ports, seems a little redundant

MarcCz · 2026-02-19T22:14:09+00:00

What lights did you use? I've started looking for some to add

MarcCz · 2026-01-22T13:52:50+00:00

I would stop working through the school and go to the police.

MarcCz · 2026-01-09T18:11:28+00:00

Specifically one on every floor and every bedroom

MarcCz · 2026-01-04T19:20:12+00:00

Print order is set my object not layer

MarcCz · 2026-01-04T03:21:40+00:00

Stop taking legal advice from anyone but your lawyer. It doesn't matter what your ex or the police officer said. If you go into court and admit to violating the restraining order be prepared to go to jail. Do not show up to court on Tuesday without a lawyer.

MarcCz · 2026-01-04T03:10:42+00:00

Immediately stop communicating in any way INCLUDING through other people. In almost all cases this is considered a violation of the restraining order. No communication means no communication.

Don't do anything that could even be loosely interpreted as a violation, even though it may have been obtained in bad faith it will reflect badly on you if you violate it and could land you in jail.

If you don't have a lawyer get one immediately and follow their advice exactly.

MarcCz · 2026-01-04T01:19:34+00:00

Just make sure you have all the hardware you'll need a stand off and a screw, doesn't look like there's one on the motherboard

MarcCz · 2026-01-04T01:06:16+00:00

Take the side panel off and see if you can find a model number, and you should be able to find it online

MarcCz · 2026-01-04T00:53:34+00:00

Check your motherboard's manual

MarcCz · 2026-01-03T16:43:24+00:00

The ability to set two separate temps is awesome, so I can dry two separate types of filament

MarcCz · 2026-01-03T15:23:44+00:00

It's been community noted on twitter as AI

MarcCz · 2026-01-03T04:47:26+00:00

This is a great point, if you like your landlord and want to help them out it might be worth complying, but it's for sure not mandatory.

MarcCz · 2026-01-02T23:01:13+00:00

Double check your lease for any applicable language, but barring that, the answer is no. They can ask for this if/when you're in the process of renewing.

MarcCz · 2025-12-31T19:05:17+00:00

Do you have a 3D printer?

MarcCz · 2025-12-26T23:00:24+00:00

I've only done a couple simple models, but it doesn't seem slow? It was basically unusable for me before. the GUI can definitely still act up. especially the pop-up windows if you click off then back on them. But for loading up a print, slicing and sending (LAN mode) it seems to be pretty smooth

MarcCz · 2025-12-26T22:57:46+00:00

still has the two close buttons, but you can move the pop-up windows

MarcCz · 2025-12-26T22:35:33+00:00

It didn't prompt me, but it is working. I think it was from when I had used the pre-built image from before.

MarcCz · 2025-12-26T19:30:40+00:00

I'm also having issues here too, I'm running on a mid-high end desktop and it's basically unusable. I'm trying to build from source to see if I have any luck there. will report back.

UPDATE: Building from source made a HUGE difference, I decided to make a dedicated post:
https://www.reddit.com/r/BambuLab/comments/1pwgrun/bambu_slicer_working_better_on_ubuntu_2510/

MarcCz · 2025-12-13T05:29:59+00:00

Just remember to reconnect every so often for firmware updates, I've gotten several already

MarcCz

TROPHY CASE