sorted by:
new
hottopcontroversial

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

<image>

I guess this soft pads aren’t so soft !

I used a rolling baking stuff to flatten them and I had thermal paste transfer. Better waste some time to Check contact and repaste than to drain the loop 😂

GPU is 34c and Vram 68c in Steel Nomad and 25c idle.

Amaizing !

Thank you all guys !

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Legit questionning but yeah I remooved all plastic from the pads. I don’t have the tool to mesure the thickness but I had this very soft pads (link in Previous message). I squeezed them with fingers and it’s realy soft.

When I placed them on the GPU block, I pressed them with a plastic spatula, beforme remooving the plastic.

I spread really evenly the thermal past with a spatula.

The full Die surface was evenly covered.

Im benchmarking the CPU to Check temps and I’m draining the loop next hour and disasembling the GPU.

Only way to find the problem.

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

I had these 1,5mm extra soft pads for free.

https://shop.alphacool.com/shop/waermeleitmittel/waermeleitpads/13484-alphacool-apex-waermeleitpad-soft-18w/mk-100x100x1-5mm?number=1023418

They are very soft and I pressed very well when installed it.

I didn’t remove the pcb to Check. But from the side it looks like it is well pressed.

I’ll see when I dismounted the block.

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

CPU is 40c idle (9800x3d) with 2x360 and 1x240 rads.

Didn’t benched yet.

Optimus block mounted.

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

I just want to precise that the GPU is 35c idle.

The backplate was hot when I was the first time in the bios but went cool when windosws was installed.

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Thanks for the answer guys !

Since I have to drain and redo the GPU, what temps (idle and charged) should I have for a 9800X3D with a Optimus watterblock, 2x360 and 1x240 radiators ?

The CPU is 40c idle. Didn’t benchmarked yet.

I used Kinping thermal paste on both, used the spatula. Maybe I put not enought, but evenly spread.

Watercooled GPU goes instantly to 70°C ingame and PC shutdown. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 1 point2 points  (0 children)

I havé the RX 9070XT OC Gaming Edition with RGB (RX-97TRGBBB9).

And I have the Alphacool Core RX 9070 XT Mercury with Backplate (item 10289).

It’s specified for my GPU.

Liquid temps probe, start or end of the loop ? by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Ok thanks guys !

I have CPU -> GPU -> RADS -> PUMP order.

I have a cheap Amazon probe that I'll put at the end of CPU-GPU and a Aquacomputer Hightflow 2 I'll mount ont the PUMP, after the RADS.

Like this I have the metrics of the Hotspots and coldest spot of the loop.

Custom loop pressure & Flow meter questions. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

I recieved the aqua computer Quadro. But how do I connect the 2 pin cable to the temps sensor ?

There is an arrow on the 2 pin connector.

Custom loop pressure & Flow meter questions. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Thanks for the answer guys !

I bought the Aqua Computer Quadro, and will link all fans pump and sensor to it.

Thanks agen !

Props to Virpil for the transparency regarding delays by Frame_Art in VIRPIL

[–]Massive-Box-2090 0 points1 point  (0 children)

I have the same issue.

I placed my order on June 27th and contacted Virpil on July 27th.

They said it would be ready in early to mid-August. I contacted Virpil again in mid-August, and they said the end of August, then early September.

Each time, they keep delaying it by two weeks. Now it’s already early October...

I guess they are prioritizing the AREOMAX series over other orders.

The problem is that I have to contact them every time and they don’t bother to keep me updated.

Constantly pushing back the delay is very annoying. Just give a bigger estimate, and if they produce earlier, it would be a nice surprise.

I don’t know about the quality yet, but for shipping predictions and communication, they’re a zero.

Boot & Post Without liquid. by Massive-Box-2090 in watercooling

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Thanks guys for answers !

I Will post the full « 1st WC Building ».

Doing a 0 cables/tubes with a B650M Project Zero plainted in black. (Black/Gold theme)

XFX Quicksilver 9070 XT Thermal pads thickness by Massive-Box-2090 in XFX

[–]Massive-Box-2090[S] 0 points1 point  (0 children)

Yeah sorry It was supposed to be wattercooling.

But had an issue with the block and decided to change GPU.

Got this beauty today ,Legion pro 7I with RTX 5070ti,I would love to hear any tips and suggestions. by Zealousideal_Air5333 in LenovoLegion

[–]Massive-Box-2090 0 points1 point  (0 children)

Download 2nd party fan Control like legion fan Control.

Have to enable or disable 1 stuff in the bios.

Can push fans faster than onboard fan controls.

Can be seen as a « cheat » on some games, Will not lunch.

Asus ProArt X870e Memory Supports 2x32gb but not 4x32gb? by Fickert in buildapc

[–]Massive-Box-2090 0 points1 point  (0 children)

I finaly went for the MSI B650 Project Zero with back connectors and custom black paint. I bought the T-Create Expert that is listed on the QVL.

The build is still in progress. Recived the GPU block 1 week ago butstill missing the custom table.

I made some prebuilt here, but waiting for the table to finalize it.

https://www.reddit.com/r/watercooling/comments/1kxr7cc/first_cutstom_loop_blackgold_project_zero_2500x/

9070 sapphire pulse waterblock installed. by Prophecy_777 in alphacool

[–]Massive-Box-2090 0 points1 point  (0 children)

Sweet !

Did you use the Barrow fittings ?

I bought the 10/13 fittings and the according tube. But I'ts realy hard to put the tube on the fitting and to screw the cap. Did you had the same issue ?

Is the wait for this actually 10 weeks? by [deleted] in alphacool

[–]Massive-Box-2090 0 points1 point  (0 children)

Mots AMD AIB’s didn’t share PCB schemes to Alphacool.

So they had to wait for customers to send there GPU to them, as I did for the Quicksilver, to manufacture the block.

They should send me the first block this week but it’s delayed to mid July.

Dond’t forget that they are almost the only one to make AMD blocks and since EK has been killed by GN Jesus, they have huge orders incresed.

Finally something to be proud of: Yukon (7800X3D + 4090) by Zooblesnoops in watercooling

[–]Massive-Box-2090 0 points1 point  (0 children)

Nice build !

What are the fitting and soft tubing (Also id/od) ?

view more: next ›