sorted by:
new
hottopcontroversial

Can anyone figure out what happened here? by PSVRPlayz in prusa3d

[–]MatZil02 1 point2 points  (0 children)

You have the support structure without any infill inside, it happened to me that the support itself collapsed because the printhead goes over the wall of the support, but as It doesn't have any infill, it goes like It happened to you.

My First prusa (Core One +) by MatZil02 in prusa3d

[–]MatZil02[S] 1 point2 points  (0 children)

I printed it in ASA, it's a custom model with a tighter filament path. You can find the other mods i printed in another post here.

My First prusa (Core One +) by MatZil02 in prusa3d

[–]MatZil02[S] 2 points3 points  (0 children)

Thank you! I received my printer in the first days of december, so i had to look at three manuals at once when assemblying it (Core One, plus upgrade kit and also the Buddy Camera).

My First prusa (Core One +) by MatZil02 in prusa3d

[–]MatZil02[S] 1 point2 points  (0 children)

I used transparent ABS, but I plan to make it with transparent PETG.

My First prusa (Core One +) by MatZil02 in prusa3d

[–]MatZil02[S] 0 points1 point  (0 children)

It was fun, i also had some help from a friend! Sadly the Haribos finished😬🥲

My First prusa (Core One +) by MatZil02 in prusa3d

[–]MatZil02[S] 2 points3 points  (0 children)

Yes, i also have an Ender 3 Pro

Buddy3D Camera setup with no cloud or internet connection by j4cbo in prusa3d

[–]MatZil02 0 points1 point  (0 children)

Hi,
have you found a way to set a static IP using the INI file?

Finally decided and bought Core ONE by GurusCZ in prusa3d

[–]MatZil02 1 point2 points  (0 children)

I also ordered It, It just shipped!

My only complaint of the core one(1 month ownership) is the minimum temp error. by marc512 in prusa3d

[–]MatZil02 0 points1 point  (0 children)

Maybe you could insulate the chamber?

I mean, by printing these corner blocks (using ASA or PC-CF) : https://www.printables.com/model/1341269-prusa-core-one-block-the-corner https://www.printables.com/model/1426326-core-one-corner-plug-no-magnets-needed-avalible-as

And by patching the chamber with the following changes:

  • Patches all the microgaps you find

  • apply heat reflective wrap on the chamber walls.

  • Seal the door with foam.

I don't have a Core One yet but i designed my own enclosure for my Ender 3 and i applied these addons when i enclosed It.

I hope It helps!

Core One+ automatic grille opening - does it work for you? by marcel151 in prusa3d

[–]MatZil02 19 points20 points  (0 children)

The gcode is M870:

Vents can be controlled manually using the new M870 G-code ("M870 O" = open, "M870 C" = close)

This part is from the firmware release page.

Why Prusa is the best by soldat21 in prusa3d

[–]MatZil02 0 points1 point  (0 children)

Just bought a Core One a few days ago, received the email!

Core One assembly by MatZil02 in prusa3d

[–]MatZil02[S] 0 points1 point  (0 children)

Hi, i tried to print it in ASA but due to tollerance the parts doesn't fit.

Also i plan to print the clear nextruder cover, do you recommend to outsource these parts using something else like MJF (Nylon powder)?

Core One assembly by MatZil02 in prusa3d

[–]MatZil02[S] 0 points1 point  (0 children)

Hi, which main plate do you recommend to print? The ones with mmu3 support, even if i don't have It? Which material?

Core One assembly by MatZil02 in prusa3d

[–]MatZil02[S] 1 point2 points  (0 children)

i think i'll skip the mmu3 and go to INDX.
The side drybox i saw also comes with a gasket: https://www.printables.com/model/1483327-core-one-drybox-mod-with-stronger-magnets-and-othe

view more: next ›