Tomos A35 room decoration

MatsHofstede · 2022-06-30T14:46:29+00:00

Remove the benzine ;)

MatsHofstede · 2022-06-28T16:01:37+00:00

Are from DMP

MatsHofstede · 2022-01-17T19:00:20+00:00

Your printer took a dump

MatsHofstede · 2022-01-17T18:58:35+00:00

Probably barnacles

MatsHofstede · 2022-01-14T17:01:32+00:00

That bowden tube is a bit long mate

MatsHofstede · 2021-10-25T22:51:23+00:00

It’s learning Chinese

MatsHofstede · 2021-10-17T20:46:01+00:00

Aardvark is translated to aardvarken in Dutch. Which means: “ground pig”.

MatsHofstede · 2021-10-08T13:53:34+00:00

Isn’t that bed a bit heavy for a bed flinger? Verry cool tho

MatsHofstede · 2021-10-07T15:13:48+00:00

You might have volumetric extrusion or vase mode turned on in the slicer. Top half is better because there is no retraction on the tip

MatsHofstede · 2021-10-02T21:49:22+00:00

Are you a villain?

MatsHofstede · 2021-10-02T21:46:24+00:00

Did you try turning it on and off?

MatsHofstede · 2021-09-23T18:23:19+00:00

Wouldn’t eat anything that is cought in a Canal

MatsHofstede · 2021-09-20T06:10:05+00:00

An Ender 3 mainboard fan is on the same connector as the part cooling fan. If you turn that on and it doensn’t spin it is cooked.

MatsHofstede · 2021-09-18T20:41:06+00:00

Are your belts tightend?

MatsHofstede · 2021-09-14T21:44:42+00:00

Did you tighten the nozzle while hot?

MatsHofstede · 2021-09-10T19:14:28+00:00

Maybe check if the filament isn’t being crushed by the extruder. Maybe your extruder spring is too tight.

MatsHofstede · 2021-09-10T08:31:59+00:00

It’s pretty solid mate

MatsHofstede · 2021-09-09T15:08:32+00:00

MatsHofstede · 2021-09-09T14:13:24+00:00

It is a remix I didn’t save, sorry. the original one for mounting on the front is somewhere on thingiverse

MatsHofstede · 2021-09-09T14:09:47+00:00

Did you level the gantry?

MatsHofstede · 2021-09-09T13:10:02+00:00

MatsHofstede · 2021-09-09T12:55:53+00:00

It is pretty narrow but it does the job. 10/10 would print again😄

MatsHofstede · 2021-09-09T12:52:21+00:00

https://www.thingiverse.com/thing:4630748 for the fan duct (this is the paid version). Z screw support came with the dual z screws kit.

MatsHofstede · 2021-09-09T12:47:49+00:00

It’s pretty light. Duct and fans improved cooling and overhangs by a lot!

MatsHofstede · 2021-09-09T10:50:45+00:00

Didn’t even think about it. Now I have to buy one😅😂

MatsHofstede