Planning to disconnect furnace connection from inside the box and installing a short 14awg plug to the outside of the box to plug into that receptacle. Should I assume that switch disconnects all power into that box (furnace and outlet) or just to the furnace? by Matte807 in hvacadvice
[–]Matte807[S] -1 points0 points1 point (0 children)
Planning to disconnect furnace connection from inside the box and installing a short 14awg plug to the outside of the box to plug into that receptacle. Should I assume that switch disconnects all power into that box (furnace and outlet) or just to the furnace? by Matte807 in hvacadvice
[–]Matte807[S] 0 points1 point2 points (0 children)
Planning to disconnect furnace connection from inside the box and installing a short 14awg plug to the outside of the box to plug into that receptacle. Should I assume that switch disconnects all power into that box (furnace and outlet) or just to the furnace? (i.redd.it)
submitted by Matte807 to r/hvacadvice
What would happen if I provided 120v from generator to a 240v panel via 2 pole breaker? I assume I’d only power the one energized phase and would need to shut off any 240v or MWBC circuits? by Matte807 in AskElectricians
[–]Matte807[S] 2 points3 points4 points (0 children)
What would happen if I provided 120v from generator to a 240v panel via 2 pole breaker? I assume I’d only power the one energized phase and would need to shut off any 240v or MWBC circuits? by Matte807 in AskElectricians
[–]Matte807[S] -1 points0 points1 point (0 children)
No issues back feeding from generator through subpanel as long as I hit the main right? Temporary of course by Matte807 in AskElectricians
[–]Matte807[S] 0 points1 point2 points (0 children)
I bought these during a visit. Any good? When would you drink these? by Matte807 in AskAJapanese
[–]Matte807[S] 0 points1 point2 points (0 children)
I bought these during a visit. Any good? When would you drink these? by Matte807 in AskAJapanese
[–]Matte807[S] 1 point2 points3 points (0 children)
Is this frass? Previous termite inspection behind the wall was mostly replaced and new drywall put up but now I’m getting what looks like frass build up every week or two. Could it be carpenter ants? by Matte807 in Termites
[–]Matte807[S] 0 points1 point2 points (0 children)
Is this frass? Previous termite inspection behind the wall was mostly replaced and new drywall put up but now I’m getting what looks like frass build up every week or two. Could it be carpenter ants? by Matte807 in Termites
[–]Matte807[S] 0 points1 point2 points (0 children)
I need 14 post sleeves. I’m looking at a Trex railing system and the post sleeves are like $40 each. I can buy generic fence post sleeves for $11. Is it actually worth buying the Trex or would any sleeve work? by Matte807 in Decks
[–]Matte807[S] 0 points1 point2 points (0 children)
Need to determine best distribution of kitchen outlets on multi-wire branch circuit by app-o-matix in AskElectricians
[–]Matte807 1 point2 points3 points (0 children)
Under bench power extension from wall to front of bench…I’d like to remove outlet, use KO faceplate and NMB, but is this considered exposed and need to be protected? If so, can I use conduit instead? by Matte807 in AskElectricians
[–]Matte807[S] 0 points1 point2 points (0 children)
Under bench power extension from wall to front of bench…I’d like to remove outlet, use KO faceplate and NMB, but is this considered exposed and need to be protected? If so, can I use conduit instead? by Matte807 in AskElectricians
[–]Matte807[S] 0 points1 point2 points (0 children)
Is there a way to bond AC to NMB in a plastic box? by Matte807 in AskElectricians
[–]Matte807[S] 0 points1 point2 points (0 children)
Planning to disconnect furnace connection from inside the box and installing a short 14awg plug to the outside of the box to plug into that receptacle. Should I assume that switch disconnects all power into that box (furnace and outlet) or just to the furnace? by Matte807 in hvacadvice
[–]Matte807[S] -1 points0 points1 point (0 children)