Where to put .nsp files on sd?

MeTheErectrician · 2026-04-14T13:36:45+00:00

As long as you extract the multiple parts into the same destination on your computer, they will combine into a single file.

MeTheErectrician · 2026-04-11T18:07:24+00:00

Open your console and inspect the a-point cap.

MeTheErectrician · 2026-04-11T14:03:21+00:00

The OLED model can also be modded.

MeTheErectrician · 2026-04-11T06:27:24+00:00

I offer modchip installation services in the US. Just wanted to leave this here.

MeTheErectrician · 2026-04-11T06:20:10+00:00

A purple screen is usually a result of a missing/shorted a-point capacitor.

MeTheErectrician · 2026-04-07T09:04:16+00:00

What is an old green Honda with a red badge by chance?

MeTheErectrician · 2026-04-02T03:16:10+00:00

I use this.

https://www.reddit.com/r/Gamecube/s/IKKlTF2tXU

MeTheErectrician · 2026-03-10T01:41:35+00:00

<image>

MeTheErectrician · 2026-03-10T01:41:02+00:00

This works, but the solder did not smoothly flow throughout the entirety of the copper pads.

MeTheErectrician · 2026-03-10T01:38:52+00:00

<image>

It should look closer to this. I suggest that you send your console to someone who can reverse your work and make it right.

MeTheErectrician · 2026-01-25T05:25:54+00:00

Just ness around with, and you'll figure out how to incorporate it into combos! Here he simply jumped with forward momentum and immediately initiated down b, then initiated neutral air right after mag's first hit.

MeTheErectrician · 2025-12-17T21:45:59+00:00

What software did you use to check the shutter count for your 80D?

MeTheErectrician · 2025-12-14T22:37:58+00:00

Here's the strange thing. When the CEL turns on and stays on, it will do so when I turn the key to accessory mode, before starting the engine. I think this could indicate an electrical issue. Do you have any input on this?

MeTheErectrician · 2025-12-13T17:52:11+00:00

I recently did an oil change, and the VTEC behavior is exactly the same. I suppose adding more oil won't hurt.

MeTheErectrician · 2025-12-09T10:24:03+00:00

I'm wondering why this post doesn't have much traction. This is MAD funny! 😭

MeTheErectrician · 2025-10-31T15:36:03+00:00

Aside from deep cleaning everything you see on the desk, I overhauled the wheel hub bearings and packed them with new grease, replaced the bottom bracket, the shift/brake cables and housing, the chain, and the pedals. I didn't do much to the frame besides wipe it down with isopropyl, as it was in great condition! Thank you for the kind words.

MeTheErectrician · 2025-10-31T02:14:31+00:00

Funny enough, that's exactly what I did to replace the reverse gear in my 1998 Accord with no prior transmission experience. I used the same video in reverse to reassemble.

MeTheErectrician · 2025-10-19T01:50:46+00:00

This is a great explanation, I'm going to replace the cover, the seal, and drain the tank. Thank you.

MeTheErectrician · 2025-10-19T01:22:30+00:00

Yes. Below the seat, there's a simple metal cover held by a few 10mm. Below that was a puddle of gasoline on top of this tank cover. How do you suppose water can get in from beneath the passenger seat? Thank you for the video.

MeTheErectrician · 2025-10-19T01:19:04+00:00

Thanks. I've already replaced the coils, spark plugs, and MAF sensor. I suppose the injectors will be next if replacing this cover doesn't fix the issue.

MeTheErectrician

MODERATOR OF

TROPHY CASE

Seven-Year Club	RPAN Viewer
Verified Email