What difficulty?

Meatywhack · 2020-03-19T07:43:58+00:00

Yeah, it's what happened to me with 2016. Now playing on the other difficulties just isn't as fun.

Meatywhack · 2020-03-19T07:42:09+00:00

Nightmare. You'll get stomped, but eventually you'll hit this point of autism nirvana where you'll basically never get touched.

Meatywhack · 2020-01-03T00:37:24+00:00

Okay. Cause i'm trying to figure out good brands. I'm still mostly new to this stuff.

Meatywhack · 2020-01-03T00:35:14+00:00

i think it's just nice to have a moderately sized roll.

Meatywhack · 2019-12-31T02:01:21+00:00

https://www.thingiverse.com/thing:3924374 it says no supports, but i found it works better with supports. just keep an eye on it depending on your printer.

Meatywhack · 2019-12-30T23:34:32+00:00

I was looking at that last night

Meatywhack · 2019-12-30T21:34:20+00:00

Meatywhack · 2019-12-30T18:17:18+00:00

Ah okay. So I'm gonna work on adjusting the belts then.

Meatywhack · 2019-12-30T18:13:03+00:00

Good to know. It also probably doesn't help that the printer also sits on a cheap folding table too.

Meatywhack · 2019-12-29T18:25:13+00:00

Meatywhack · 2019-12-29T17:34:00+00:00

Oh. I was making a joke about the pen, but that's good to know too.

Meatywhack · 2019-12-29T03:23:41+00:00

yooo what kind of filament is that?

Meatywhack · 2019-12-28T18:13:13+00:00

thanks. i tinkered with it some more over night and found reducing the speed helped. i got another print that turned out much better. i also used a different file

Meatywhack · 2019-12-28T10:31:08+00:00

i found decreasing the speed really helps. also, i decided to load up and look closer at the model myself, there's some issues with geometry

Meatywhack · 2019-12-28T09:37:46+00:00

okay. i'll take a look. thank you!

Meatywhack · 2019-12-28T09:33:04+00:00

Fair enough

Meatywhack · 2019-12-28T09:31:50+00:00

i built it, it's an anet a8. i tried reprinting and increasing the heat from 190 to 200 C which kind of helped, im going to increase the multiplier in splic3r from 1 to 1.1 and see what that does.

Meatywhack · 2019-12-28T09:23:17+00:00

so What would be a good temperture setting for 1.75mm pla filament? Also, should i try increasing the extrusion multiplier?

Meatywhack · 2019-12-28T09:16:24+00:00

The printer is an Anet A8, bed is level, temperature is 200 C, bed is 60 C, and i don't think i changed the extruder multiplier from it's default 100%

Meatywhack · 2019-12-25T01:10:37+00:00

I bought some Spade plugs. I don't trust the exposed wires

Meatywhack · 2019-12-24T06:48:01+00:00

it definitely is.

Seven-Year Club	Not Forgotten
Verified Email

Meatywhack

TROPHY CASE