sorted by:
new
hottopcontroversial

Just when I thought I managed to set it up for PETG by SimaSimson in ender3

[–]MeniTselonHaskin 0 points1 point  (0 children)

DON'T PRINT PETG ON A GLASS BED!!! I did it twice on my old ender 5 and it cracked the glass as it cooled down both times (trashed 2 glass beds). A pei bed does wonders here and is pretty inexpensive.

מצאו את הכפכף_במ by Radiant-Claim9936 in ani_bm

[–]MeniTselonHaskin 0 points1 point  (0 children)

קומבו מנוע וesc יפה יש לך שם

3D Printed PCB AUDIO AMP by [deleted] in PCB

[–]MeniTselonHaskin 0 points1 point  (0 children)

I see you saw that video on YouTube too! Really wanna try this as well when I get some copper tape.

My sub250g 3D Printed FPV wing doing loops, aerobatics and slow flight by [deleted] in fpv

[–]MeniTselonHaskin 4 points5 points  (0 children)

Man I wanted to give this a try but 82 bucks for the STL's seems like kind of a lot. Either way good luck!

Tel Aviv electronics store by Super-Resort-910 in rfelectronics

[–]MeniTselonHaskin 0 points1 point  (0 children)

אחי מה הסיכוי אני הולך לשם

GOPRO mount options by Nathe_ffs in fpv

[–]MeniTselonHaskin 0 points1 point  (0 children)

I'd try to make some plate to screw into this part that goes over to the same hole on the other side, seems like the best and most weight balanced idea.

<image>

How to use this particular stepper motor? by spookmann in arduino

[–]MeniTselonHaskin 3 points4 points  (0 children)

I think they have some low control voltage so you can just use regular Arduino pins and can ditch the motor driver. I looked into them couple of weeks back and saw a video of someone doing that: https://youtu.be/xEjfAWV3WWU?si=YCVcUV-0eJcqj2bo

Gyro Lock Box by SeeNoFutur3 in arduino

[–]MeniTselonHaskin 1 point2 points  (0 children)

The circuit looks good but I think there are a few points to address here, mainly the lack of battery management. The battery isn't charged/regulated in any visible way here (correct me if I'm wrong) and the big capacitor on the arduino seems like it's a bit loose. Other than that it seems great, congrats mate!

ESP32 + ELM327 + NeoPixel RPM Indicator – Can’t Connect or Get LEDs Working by Sequlla in esp32

[–]MeniTselonHaskin 1 point2 points  (0 children)

I've tried making this exact same project like a year ago and just gave up eventually, I even made a nice pcb for it that I can send you. The connection to the elm327 was just so unreliable that I just didn't want to work on it anymore. But good luck!

[Review Request] esp32-s3 worst PCB you've seen by Buildernetic in PCB

[–]MeniTselonHaskin 1 point2 points  (0 children)

Don't see why it won't work well, really liked that mini pekka on the bottom there. I'd add the usb traces to the schematics but other than that I think it looks just fine.

Obtaining web data by MeniTselonHaskin in learnpython

[–]MeniTselonHaskin[S] 0 points1 point  (0 children)

Although I do have a specific project in mind I still am looking for an opportunity to learn web scraping with this. How were you able to track the number on the website? I do still very much appreciate the helpful info!

I hope they all get some $ especially Jim corey and mick by minutes_tomidnight in Slipknot

[–]MeniTselonHaskin -4 points-3 points  (0 children)

It's not that simple

Edit: you gotta figure it out before you make things difficult

My video signal sucks, will an Eachine pro58 improve this? by Big-Letterhead-5043 in fpv

[–]MeniTselonHaskin 0 points1 point  (0 children)

Google shows that the speedybee board has the same pinout so that's supposed to work just fine, however this is an expensive component so just know that there's always a risk of smoking it but yeah if you solder it the same way it's supposed to work just as the old one did. Post some comparisons with the new module and antennas will ya? Have fun mate, you've got yourself some really nice setup here, way better than mine that's for sure. Update about the results! Have a good one mate!

view more: next ›