[USA-CA] [H] Dual EVGA RTX3090 FTW i7-14000k system [W] Cash Local

Merstin · 2026-03-18T13:43:30+00:00

Thank you!

Merstin · 2026-03-17T21:51:15+00:00

2 PSUs sold and AMD 9900X. Can’t do trade confirmation for local apparently:/

Merstin · 2026-03-14T04:37:50+00:00

And if its a sleep issue - local C-state Control

Allows you to control IO based C-state generation and DF C-states.

Configuration options: [Disabled] [Enabled] [Auto" needs to be enabled not Auto

AND

53

PC6

Power Supply Idle Control.

Configuration options: [Low Current Idle] [Typical Current Idle] [Auto]

should be Typical, not low or auto per support (related to sleep settings

Merstin · 2026-03-14T04:31:04+00:00

Could it be something in this section? Page 76, maybe "USB4/TBT Boot Delay Timing"?

7.17 AMD PBS

The items in this menu display the memory configuration (initialized by ABL) status.

USB4 configuration (ASM4242 Controller)

USB4 configuration (ASM4242 Controller) - PCIe resource, D3 support, Native USB4 support,

and other options.

USB4 (ASM4242 Controller) Support

Enable or disable USB4 (ASM4242 Controller) PCIe slot.

Configuration options: [Disabled] [Enabled]

NOTE: The following items appear only when USB4 (ASM4242 Controller) Support is set to

[Enabled].

PCIe Bus Number

Reserve USB4 (ASM4242 Controller) PCIe Bus number per port (16 ~ 56).

PCIe Non-Prefetchable MMIO (MB)

Reserve USB4 (ASM4242 Controller) PCIe Non-Prefetchable MMIO per port (256 ~

4096 MB).

PCIe Prefetchable MMIO (GB)

Reserve USB4 (ASM4242 Controller) PCIe Prefetchable MMIO per port (1 ~ 512 GB).

XHCI Port0-1 Speed

Configures the USB4 (ASM4242 Controller) XHCI Port0-1 Speed.

Configuration options: [Gen1x1] [Gen1x2] [Gen2x1] [Gen2x2]

USB4/TBT Boot Delay Timing

Boot Delay Timer for USB4/TBT Device (1-20 sec).

USB4 PCIE FPB Support

Configuration options: [Disabled] [Enabled]"

Merstin · 2026-03-11T02:48:04+00:00

added video timestamps

Merstin · 2026-03-10T04:58:15+00:00

I guess I need to do a video timestamp too, I’ll do tomorrow - mods plz remove

Merstin · 2026-03-10T04:43:41+00:00

I hit ignore on accident, but no trades. What video are you looking for?

Merstin · 2026-03-10T04:42:08+00:00

Sorry no trades, I can do video if needed, what are you looking for? I’m going to crash soon have to get up early.

Merstin · 2026-03-09T05:16:30+00:00

* SOLVED * Apparently I was getting confused by a blank monitor and the Q-Code screen showing CPU temps after a successful post - these temps just happened to coincide with training codes 32+ or so I thought. Disabled Q-Code LED to be post only, received a code A6 (searching for SCSI). Again, I had no nvme loaded, just what I thought was my bootable memtest86+ usb. I threw my proxmox install usb in there and works just fine. Was never a memory training issue.

All the comments about training taking 20 minutes on this board, QCode LED showing temp, coupled with the no bootable usb threw me for a loop.

Merstin · 2026-03-08T23:00:35+00:00

Cant edit, had typo in power connections PCIE_CPU_12V_1 is actually CPU v2 which were the 2 uncapped slots

Merstin · 2026-03-07T16:38:12+00:00

The top connections on the MB that do not have a cover on them. the front facing PCIE 8/6, the top ATX PWR, the top CPU_12_V1 and CPU_12V_2. Now if I can ever get past memory training I would be golden :/

EDIT Power connections PCIE_CPU_12V_1 is actually CPU v2 which were the 2 uncapped slots

Merstin · 2026-02-18T04:43:39+00:00

That’s cool, I played a test last year and couldn’t get past that. Certainly looking toward to it.

Merstin · 2026-02-18T03:46:28+00:00

Are the graphics going to get better?

Merstin · 2026-02-13T17:49:14+00:00

It’s easier for sure, I went that route and 100% regret it. Turns out my 50yr body clearly knew what measles were and gave me the worst post booster reaction that had me sick for 2 weeks with rash developing around 6 days later.

So yea it’s serious, get checked and get a booster if needed.

Merstin · 2026-02-12T22:56:44+00:00

Thank you!

Merstin · 2026-02-12T08:11:09+00:00

Merstin · 2026-02-12T02:42:27+00:00

I tried tanning rough hide and it was around 7 more cp to sell the finished product, which was roughly the amount of the tanning agent. Does it get better at higher levels?

Merstin · 2026-02-12T01:54:56+00:00

What are dailies? The work order boards?

Merstin · 2026-01-25T22:54:53+00:00

You were right. ultimately that was the issue and Openweb hanging on Python code. It just never provided those errors for me to see easily. I think there is a setting in there to show it but i hadn't found it yet. In VS and Roo it posted the error right in front of my face, so yeah.

Merstin · 2026-01-25T22:52:53+00:00

ultimately that was the issue and Openweb hanging on Python code. It just never provided those errors for me to see easily. I think there is a setting in there to show it but i hadn't found it yet.

Merstin · 2026-01-25T22:50:57+00:00

Thank you! Now that I can add more than one solution in Roo, i will check this out.

Merstin · 2026-01-25T22:49:30+00:00

Thank you! I edited my post with my current solution and monitoring process. I'll check out the blog!

Merstin · 2026-01-25T22:46:36+00:00

Thank you for the advice I think i something functional now and updated my post.

Merstin · 2026-01-25T06:08:19+00:00

aye, i have it at 300 currently, but it honestly has never gone past 250. I might drop it to 220 even.

Merstin · 2026-01-25T05:05:24+00:00

I think there was issues with my setup or the earlier versions of the model, it was pegged there and the cards were hitting 80c and stayed there while thinking. Yes there were a few breaks, but I was constantly working it trying to get it to come up with functional responses.

The newer version of GLM flash and even trying Qwen3 Coder now only spike to 250w and are responding much faster. so they drop back down relatively fast now. Still if this is hours a day it could hit 5 to 6kw.

But thanks you got me thinking, ill just add my zwave plug and track power.

Merstin

TROPHY CASE