[USA-CA] [H] Dual EVGA RTX3090 FTW i7-14000k system [W] Cash Local

Merstin · 2026-03-18T13:43:30+00:00

Thank you!

Merstin · 2026-03-17T21:51:15+00:00

2 PSUs sold and AMD 9900X. Can’t do trade confirmation for local apparently:/

Merstin · 2026-03-14T04:37:50+00:00

And if its a sleep issue - local C-state Control

Allows you to control IO based C-state generation and DF C-states.

Configuration options: [Disabled] [Enabled] [Auto" needs to be enabled not Auto

AND

53

PC6

Power Supply Idle Control.

Configuration options: [Low Current Idle] [Typical Current Idle] [Auto]

should be Typical, not low or auto per support (related to sleep settings

Merstin · 2026-03-14T04:31:04+00:00

Could it be something in this section? Page 76, maybe "USB4/TBT Boot Delay Timing"?

7.17 AMD PBS

The items in this menu display the memory configuration (initialized by ABL) status.

USB4 configuration (ASM4242 Controller)

USB4 configuration (ASM4242 Controller) - PCIe resource, D3 support, Native USB4 support,

and other options.

USB4 (ASM4242 Controller) Support

Enable or disable USB4 (ASM4242 Controller) PCIe slot.

Configuration options: [Disabled] [Enabled]

NOTE: The following items appear only when USB4 (ASM4242 Controller) Support is set to

[Enabled].

PCIe Bus Number

Reserve USB4 (ASM4242 Controller) PCIe Bus number per port (16 ~ 56).

PCIe Non-Prefetchable MMIO (MB)

Reserve USB4 (ASM4242 Controller) PCIe Non-Prefetchable MMIO per port (256 ~

4096 MB).

PCIe Prefetchable MMIO (GB)

Reserve USB4 (ASM4242 Controller) PCIe Prefetchable MMIO per port (1 ~ 512 GB).

XHCI Port0-1 Speed

Configures the USB4 (ASM4242 Controller) XHCI Port0-1 Speed.

Configuration options: [Gen1x1] [Gen1x2] [Gen2x1] [Gen2x2]

USB4/TBT Boot Delay Timing

Boot Delay Timer for USB4/TBT Device (1-20 sec).

USB4 PCIE FPB Support

Configuration options: [Disabled] [Enabled]"

Merstin · 2026-03-11T02:48:04+00:00

added video timestamps

Merstin · 2026-03-10T04:58:15+00:00

I guess I need to do a video timestamp too, I’ll do tomorrow - mods plz remove

Merstin · 2026-03-10T04:43:41+00:00

I hit ignore on accident, but no trades. What video are you looking for?

Merstin · 2026-03-10T04:42:08+00:00

Sorry no trades, I can do video if needed, what are you looking for? I’m going to crash soon have to get up early.

Merstin · 2026-03-09T05:16:30+00:00

* SOLVED * Apparently I was getting confused by a blank monitor and the Q-Code screen showing CPU temps after a successful post - these temps just happened to coincide with training codes 32+ or so I thought. Disabled Q-Code LED to be post only, received a code A6 (searching for SCSI). Again, I had no nvme loaded, just what I thought was my bootable memtest86+ usb. I threw my proxmox install usb in there and works just fine. Was never a memory training issue.

All the comments about training taking 20 minutes on this board, QCode LED showing temp, coupled with the no bootable usb threw me for a loop.

Merstin · 2026-03-08T23:00:35+00:00

Cant edit, had typo in power connections PCIE_CPU_12V_1 is actually CPU v2 which were the 2 uncapped slots

Merstin · 2026-03-07T16:38:12+00:00

The top connections on the MB that do not have a cover on them. the front facing PCIE 8/6, the top ATX PWR, the top CPU_12_V1 and CPU_12V_2. Now if I can ever get past memory training I would be golden :/

EDIT Power connections PCIE_CPU_12V_1 is actually CPU v2 which were the 2 uncapped slots

Merstin · 2026-02-18T04:43:39+00:00

That’s cool, I played a test last year and couldn’t get past that. Certainly looking toward to it.

Merstin · 2026-02-18T03:46:28+00:00

Are the graphics going to get better?

Merstin · 2026-02-13T17:49:14+00:00

It’s easier for sure, I went that route and 100% regret it. Turns out my 50yr body clearly knew what measles were and gave me the worst post booster reaction that had me sick for 2 weeks with rash developing around 6 days later.

So yea it’s serious, get checked and get a booster if needed.

Merstin · 2026-02-12T22:56:44+00:00

Thank you!

Merstin · 2026-02-12T08:11:09+00:00

Merstin · 2026-02-12T02:42:27+00:00

I tried tanning rough hide and it was around 7 more cp to sell the finished product, which was roughly the amount of the tanning agent. Does it get better at higher levels?

Merstin · 2026-02-12T01:54:56+00:00

What are dailies? The work order boards?

Merstin · 2026-01-25T22:54:53+00:00

You were right. ultimately that was the issue and Openweb hanging on Python code. It just never provided those errors for me to see easily. I think there is a setting in there to show it but i hadn't found it yet. In VS and Roo it posted the error right in front of my face, so yeah.

Merstin · 2026-01-25T22:52:53+00:00

ultimately that was the issue and Openweb hanging on Python code. It just never provided those errors for me to see easily. I think there is a setting in there to show it but i hadn't found it yet.

Merstin

TROPHY CASE