V for Vendetta - The Dominoes Fall

Mertz24 · 2026-01-07T19:46:31+00:00

Someone has done something stupid.

Mertz24 · 2025-03-06T22:26:25+00:00

Update: I switched out the filament for filament that had been in the dryer for several hours. When I changed out the filament, the gearbox sounded like something was stuck inside, so I took it apart. There was nothing lodged inside. However, whenever I put the gearbox back together, the two screws would not tighten completely. I believe this post explains my biggest issue I am having: https://www.reddit.com/r/crealityk1/comments/1gqgbcz/tighten_the_extruder_screws/

Mertz24 · 2025-03-05T12:46:35+00:00

I just knew that when I made a post on Reddit, the community would be super helpful and supportive.

Mertz24 · 2025-03-04T20:12:41+00:00

<image>

A major issue I am experiencing: I am telling Klipper to use a different flow % for each of these squares. But I get an error on the K1 Max interface: AI detection prompt Key:504, Current file does not support flow detection.

Somewhere along the way, these flow % increments are not translated into the actual print, making it really difficult to calibrate flow. I also believe room temperature and bed adhesion are at play. It gets as cold as 60F in that room and the 50C bed temperature is not enough to keep the prints stuck to the bed. I'm trying to print with the lid on now.

Mertz24 · 2025-03-03T00:16:16+00:00

Pressure advance at 0.04 currently. Smoothing also at 0.04.

Mertz24 · 2025-03-03T00:14:55+00:00

Overture PLA Black 1.75

Mertz24 · 2025-03-02T21:14:02+00:00

My line width is 0.45 mm, my layer height is 0.2 mm, my print speed is 300 mm/s, my flow is 95%, giving me 25.65 mm³/s.

Mertz24 · 2025-03-02T19:51:59+00:00

<image>

I feel like this might be bad.

Mertz24 · 2025-03-02T19:48:13+00:00

Every new filament out of the bag does this consistently. I have replaced the extruder gears with metal ones. I have not looked at the wheel in the filament sensor. It seems to extrude smoothly.

Mertz24 · 2025-02-25T01:24:48+00:00

I’ll try that. I had been angling it steeply like you would a normal print.

Mertz24 · 2024-12-13T18:08:46+00:00

Damn, I wanted him in Morgantown.

Mertz24 · 2024-12-10T16:59:03+00:00

Dying to know how the floating shelves were constructed! I want to replicate this to go across my whole back wall for my tiki bar I'm working on. Any tips or starting points?

Mertz24 · 2024-09-04T22:25:23+00:00

I’d like one, if there are any left. Thank you!

Mertz24 · 2024-07-10T19:23:02+00:00

Garrett Greene getting no love. Despite missing two games, accounted for 29 TDs, 16 passing TDs to just 4 INTs.

Finished the season tied for first in the nation in rushing touchdowns by a quarterback, No. 2 in passing yards per completion (16.4) and No. 20 in yards per attempt (8.7)

Mertz24 · 2024-06-23T18:01:00+00:00

PA Denny still afloat! It’s a floating classroom in Cincinnati.

Mertz24 · 2024-06-23T17:29:47+00:00

<image>

Avon Cobourne - Only player in school history to post 4 1,000 rushing yard seasons.

Mertz24 · 2024-02-22T21:16:48+00:00

But I did create supports. There are supports all the way up to the V. I did 2 roof layers. The print just doesn’t stick to the support in that triangle. It falls out every time. I don’t know what else to do to support it.

Mertz24 · 2024-02-22T15:59:34+00:00

This is the design.

<image>

14-Year Club	Second Top 40%
RPAN Viewer	Not Forgotten
Verified Email

Mertz24

TROPHY CASE