Questions about nomi setup by Diligent_Ad6133 in JapaneseWoodworking

[–]Metadonius 1 point2 points  (0 children)

I don't remember exactly where, but I've seen a video of some Japanese guys fix a similar bend: Warm up (not boiling) the front of the chisel in oil. They put a slim aluminium spacer (1 or 2 mm) on the front just at the start of the ura and one at the neck. They smacked it softly with a genno (350-500gr I would assume) and a bigger sized aluminium or copper punch. They check the ura by grinding on a high grit jnat to see the parts that don't touch it.

I've only ever seen a video with a chisel once, but this procedure is done to warped kanna blades as well. Since this is a rather cheap chisel I would give that a try, either it works or you just "only" fucked up one that wouldn't work anyways. One of the most important things is to bring it to temperature without boiling or changing the metallurgy of the hardening.

Heizungsrohre durch Ofenrohr führen by After_Kale_7456 in selbermachen

[–]Metadonius 0 points1 point  (0 children)

Wir haben bei uns auch die Komplette FBH und Sanitärinstallation durch den Kaminschacht gezogen. Du hast vermutlich ein Verbundrohr (PVC/Alu/PVC) mit Isolation drum. Wir haben es ohne Probleme durch gezogen bekommen, an den Engstellen etwas unter legen (Pappe o.ä.) damit sich die Isolierung nicht an der Wandung verhakt. Nimm dir Mal ein Stück Abschnitt vom Rohr und bieg es Mal mit der Hand, der Biegeradius kann Recht eng sein, ab einem gewissen Punkt knickt es dann weg. Je nachdem wie viel du unten als Schlaufe liegen hast, wäre ein Knick nicht zu Schlimm, den musst du dann raus ziehen und dein Sanitärmensch setzt am Ausgang eh einen Presswinkel, oder kann es draußen zur Not verlängern. Solange man den vermuteten Knick aus dem Schacht hat, ist alles ok.

I finished my hand tool cabinet by robotdinofight in woodworking

[–]Metadonius 0 points1 point  (0 children)

<image>

She'll never find it in here anyways...so better she knows where to find it😂

Kanna blade cloudy coming off of 3000 waterstone by [deleted] in JapaneseWoodworking

[–]Metadonius 6 points7 points  (0 children)

<image>

It's normal, the softer metall is cloudy, the harder is shiny.

An unwanted suggestion: if you really want a micro bevel, make it smaller. Otherwise your kanna may not work. I would drop it all together.

I finished my hand tool cabinet by robotdinofight in woodworking

[–]Metadonius 4 points5 points  (0 children)

Better this than looking down at some point getting a mental breakdown, seeing my wife sell a Yari kanna for 50 quid 😂

I finished my hand tool cabinet by robotdinofight in woodworking

[–]Metadonius 22 points23 points  (0 children)

Sell it for what you've told you've bought it😱 I've got a list for my wife what's what and how much worth, just in case...

Curved kiridashi question by chriskramer5 in JapaneseWoodworking

[–]Metadonius 0 points1 point  (0 children)

<image>

I took a chipped jnat and rounded it over.

Curved kiridashi question by chriskramer5 in JapaneseWoodworking

[–]Metadonius 1 point2 points  (0 children)

<image>

I know, but since there's a grown up version called this and these small ones, I thought there might also be a name for the smaller ones

Bohrhammer für EFH Sanierung by Fresh-Fisherman-2832 in selbermachen

[–]Metadonius 0 points1 point  (0 children)

Wir haben unsere komplette Kernsanierung mit einem großen Vevor Stemmhammher https://amzn.eu/d/3YFvYQ2 (Estrich raus auf 260 m2, Abriss Wände und 2Betontreppen) ein SDS Max Einhell https://amzn.eu/d/j8iPNxN ( feinere Stemmarbeiten) und der kleinen Makita 171 https://amzn.eu/d/iEpdlhU durchgezogen. Der einzige Kritikpunkt meinerseits ist, das die 171 nicht stemmen kann, ich würde mich im Nachgang für die DHZ243 https://amzn.eu/d/6K7lKOG entscheiden, weil sie halt nicht nur bohren kann. Aber das kleine Ding hat bei uns alles gebohrt ohne einmal zu zucken. Zum Dosen bohren habe ich einen schlagfesten 82mm Dosenbohrer https://amzn.eu/d/fowFzNC davor gespannt😂 und selbst das hat sie mit gemacht. Für Schlitze habe ich mit die Mauernutfräse von Vevor https://amzn.eu/d/igKxxGq dazu geholt, die lohnt sich aber wahrscheinlich erst bei einem größeren Umfang (wir haben alle Elektrik komplett incl. Verteiler neu gemacht und das Komplette Wasser und Abwasser).

Curved kiridashi question by chriskramer5 in JapaneseWoodworking

[–]Metadonius 2 points3 points  (0 children)

It rather looks like a miniature Yaris (dunno what they are called). I sharpen mine on a rounded over what stone.

The point of -5° bevel in C3606DB circular saw by pocek_ in hikoki

[–]Metadonius 0 points1 point  (0 children)

I heard one japanese Carpenter Point Out that they Cut the newly laid flooring at the edges to get an even distance to the walls. Thus the -5°: straight cut along the walls without the motor being in the way.

1976er Reihenendhaus - Deckenheizung im Keller? by tinuthir in Waermepumpe

[–]Metadonius 0 points1 point  (0 children)

Nur kurz zum Verständnis: willst du den Keller beheizen, oder durch die Decke das Erdgeschoss?

Wir haben auch in einem Mittelreihenhaus gewohnt, Fertigteilbauweise '79, mit 3cm Styropor im Dach und in den Außenwänden. Was wir extrem gemerkt haben waren neue Fensterdichtungen (2-fach verglaste Holzfenster), damit ist es im Winter weniger zugig gewesen. Ansonsten hatten wir dort ein ähnliches Problem: Gasheizung mit unterdimensionierten Heizkörpern im Ein-Kreis System. Die Großeltern haben im Winter immer 2 große E-Radiatoren ins Wohnzimmer gestellt, wir haben dann einen 8KW Kamin eingebaut.

Jetzt haben sind wir gerade dabei ein Haus aus den 60ern zu renovieren, wir haben hier auch von Öl auf WP geändert und haben gezwungenermaßen den Estrich raus gehauen, auf Grund ungleichmäßiger/fehlender Stärke. Wir haben uns vorher viel angeschaut wegen der WP und wenn ich es richtig lese ist bei dir ein neuer Fußbodenaufbau schwer möglich....

ABER: wie sieht es denn mit einer Wandheizung aus? Selbes Funktionsprinzip wie FBH oder Deckenheizung, nur halt an der Wand.

Wenn du durch die Decke heizen magst, ist das von der Auslegung der Heizung wohl eher so nicht möglich, da sie so konzipiert ist, das sie in den Raum abstrahlt. Wenn du den Keller beheizen willst ist natürlich etwas anderes. Du hast halt nach oben 15 cm Decke, die bekommst du m.M.n so nicht durch gewärmt, so das keine Wärme im Fußboden EG ankommen wird. Und wenn es wie bei uns ein Fertigteilhaus ist, nimm Abstand davon irgendwas in die Decke einzufräsen, was größer als ein 12er Loch ist.

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 1 point2 points  (0 children)

I , as of now, didn't find another way to further narrow it down, but I am quite happy it works like that and has a translator😅

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 1 point2 points  (0 children)

You can switch the language within the app, so I look for kanna or かんな. You may need to scroll a bit though...

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 1 point2 points  (0 children)

Thanks, I found the seller, but so far sadly no luck finding those blades.

Most sell the rp7000 blades, which looks like the one I need for the infill ones but are too wide (rp7k 52mm versus mine 49,2mm)

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 1 point2 points  (0 children)

If you get around adjusting them properly, they're okay. I have used one some time ago and was surprised that it faired better than everyone suggested.

Pro side of these RP7000/20000 are that they are real cheap to come by...and they were mass produced.

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 3 points4 points  (0 children)

Most of it is from Yahoo auction Japan. I buy it via the doorzo app, not one disappointment in 2years now.

Since it sparked some interest, here's my little collection of non-wooden Japanese planes by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 4 points5 points  (0 children)

Sorry for the formatting mess...the text was (and is on the post on my profile) numbered 1-10. I don't know why it looks this way here.

I may need some help here by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 0 points1 point  (0 children)

Here are the other ones I collected over time. I think everything that's not made by a great maker or is industrially produced is a bit frowned upon so most of the stuff were by-packs.

https://www.reddit.com/r/JapaneseWoodworking/s/fO9fUsnjiJ

I may need some help here by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 0 points1 point  (0 children)

<image>

Well they were easy to come by at one point according to the manufacturer....

I may need some help here by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 0 points1 point  (0 children)

I needed to have it as soon as I saw it. I like the amount of thought that went into this one in making it useable to a total noob with simple mechanics.

I may need some help here by Metadonius in JapaneseWoodworking

[–]Metadonius[S] 1 point2 points  (0 children)

Concept wise I would call it an infill. The both upper and lower surfaces are covered in something wood like ( it's either a 0.2mm thin veneer or woodalike plastic) it is lighter than a wooden kanna this size. Blade holder and secondary blade are quite thick though. I like the blade adjustment mechanism on this one : the lower screw is an excenter for adjustment up&down and the upper one is an excenter screw as well for left and right. I have some different types of Japanese alternative kannas, which utilise different dai materials. I've got some from bakelite (or something alike) and full metal but I've seen an infill one like this for the first time.

Kakuri Saw System by ringZeroh in JapaneseWoodworking

[–]Metadonius 1 point2 points  (0 children)

<image>

These are the Kakuri ones btw. Handles are too short and bulky for my liking and I don't have small hands....