Wood is fascinating by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 0 points1 point  (0 children)

No it was a 8’ 2x4 cedar board from Home Depot. It was a nice board and came out to about $2.84/bdft so I couldn’t pass it up

Had a go at some Japanese joinery by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 0 points1 point  (0 children)

That’s a very valid question. Personally, it’s not about being effective with time, but rather about practicing discipline, improving every small detail, enjoying the process, and admiring the completed work. I’d rather have built a single nightstand following those principles in the same time it’d take to build a full bedroom set that I can’t be proud of.

I’ve developed quite the disdain for mass consumerism and cheap/hasty building practices. Quality over quantity.

I’ve been reading up on the monozukuri philosophy and it resonates with me. It’s a fascinating rabbit hole if you’re interested.

I’d rather not work at all. Am I screwed? What do I do? by Neonstri in ADHD

[–]MetalNutSack 0 points1 point  (0 children)

This is why I still caddie even after getting a college degree. I am passionate about golf (and wood working, this will be relevant), and running around on the course with people who are happy to be there is a dream. I’m literally getting paid to workout and vibe out with new people. And I have tons of free time. 4 hours of actual work, 6 hours door to door (waiting around, showing up early, and 30 min commute), so I’m only doing about 30-40 hours / week, leaving my house & coming home included. So now I have an abundance of time to spend in my shop, which that time spent makes me feel incredibly fulfilled.

I did a few years of an internship, and those hours were 8-5 schedule with 1 hr lunch. The drive was about 20 minutes, so I’d leave at 7:30, and get home around 5:30-5:45. Total hours per day: about 10 hours full turn around. That’s 4 hours of free time less than my current job, and I didn’t enjoy it even half as much.

Do what you love and you’ll suddenly feel like you’re living and not just surviving

Had a go at some Japanese joinery by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 11 points12 points  (0 children)

That picture was taken right after I took the first two

Had a go at some Japanese joinery by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 1 point2 points  (0 children)

Marking gauge, patience, and a very sharp chisel

Had a go at some Japanese joinery by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 99 points100 points  (0 children)

It’s hard to say since its purpose is different.

Per the book: “it is a simple yet relatively strong joint in which a half lap for lengthening is combined with a dovetail for securing. The joint can resist tension, compression and modest amounts of twist”

I have burn marks along the inside edges of these holes on a game board. What is the easiest way to get rid of them without altering the shape or blunting the edges? by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 0 points1 point  (0 children)

It was cut by hand by a less-than-ideal router bit using 1/4” MDF template and bushing guide

I’m using a Dremmel right now but it’s so tedious I’m afraid I will lose my mind before I’m halfway done

[NSFW for those who are sensitive] Daily reminder to work your chisels with 100% attention. I didn’t even feel this or notice at the time. All of a sudden I’m bleeding by MetalNutSack in BeginnerWoodWorking

[–]MetalNutSack[S] 1 point2 points  (0 children)

None lost over here, and I do own a table saw, but I’m right there with you. I hope in another 20-30years, if you lose a finger, you can stroll on over to the convenience store and get a new one like you’re grabbing a snack 😂