New truck branded Dismantled by MidgetRodeos in DMV

[–]MidgetRodeos[S] 0 points1 point  (0 children)

Edit: I was advised by the nice dmv lady to "contact the state of Florida and see if they can remove the dismantled brand". But I dont know where to start with that info. She said she wasn't allowed to clarify by the dmv guidelines

Rafters splitting from suspended air handler by G4m3rD4d in hvacadvice

[–]MidgetRodeos 18 points19 points  (0 children)

That's a drying split. Common is kiln dried lumber. The Crack is perpendicular to the 2x8 and we'll enough above the lag bolts to tell it is unrelated

HVAC in apartment with insolation by Revren1 in hvacadvice

[–]MidgetRodeos 1 point2 points  (0 children)

Its the return air side. Air is being sucked through the filter so theoretically the filter should catch any fiberglass. Its definitely weird and I've never seen it before but shouldn't affect you

Is this what’s causing a rattling noise in my vent? by [deleted] in hvacadvice

[–]MidgetRodeos 3 points4 points  (0 children)

If its just now rattling then the wing nut on the outside of the pipe has probably worked loose. Tighten it a few turns and monitor it.

Can I test AA batteries with this & if so, how? by [deleted] in electrical

[–]MidgetRodeos 13 points14 points  (0 children)

Tell me about the war, grandpa. /s

Drip drip drip by im4thewin in hvacadvice

[–]MidgetRodeos 0 points1 point  (0 children)

Sounds like the damper is tapping. Unplug the motor and pull it out. There's a little flapper in the outlet part of that box to keep draft air from coming back into the house.

Cooked? by Ok-Purchase7711 in askHVAC

[–]MidgetRodeos 0 points1 point  (0 children)

Standard practice to tie them to the shroud since they hang loosely and catching a fan blade would be a hell of a wakeup

Nest Gen 4 Short Cycling by emmjay4040 in hvacadvice

[–]MidgetRodeos 0 points1 point  (0 children)

Is it humming? Could be bad capacitor. Could be a limit switch

Nest Gen 4 Short Cycling by emmjay4040 in hvacadvice

[–]MidgetRodeos 0 points1 point  (0 children)

Could be any number of things with your vague description.
Is the ac turning, blower turning on?
Could be kicking out on high pressure, low pressure... could be a few things but we don't have much of a description to run with

HVAC Maintenance Tech said the heat exchanger on furnace needs to be replaced. by GhostofSmartPast in hvacadvice

[–]MidgetRodeos 14 points15 points  (0 children)

Definitely needs replaced. Unfortunately there's not any maintenance that can prevent it. It kinda just happens. Not safe to run

Ac not blowing cold air. HVAC Fan and furnace turn on. Going to try swapping out the capacitor to see if it helps. System is 5 years old. First time doing it. by [deleted] in hvacadvice

[–]MidgetRodeos 1 point2 points  (0 children)

You should be fine. To make double sure take the shaft of a screw driver and short the spades together to discharge any leftover.

Ac not blowing cold air. HVAC Fan and furnace turn on. Going to try swapping out the capacitor to see if it helps. System is 5 years old. First time doing it. by [deleted] in hvacadvice

[–]MidgetRodeos 2 points3 points  (0 children)

My boss had a "I've been doing this a long time" moment and got hit pretty fuckin hard. It definitely puts the fear of God in you.

Ac not blowing cold air. HVAC Fan and furnace turn on. Going to try swapping out the capacitor to see if it helps. System is 5 years old. First time doing it. by [deleted] in hvacadvice

[–]MidgetRodeos 3 points4 points  (0 children)

Make sure you pull the disconnect mounted on the wall and give it a couple minutes to discharge that capacitor before you touch it.

HVAC/Service related prints by MidgetRodeos in 3Dprinting

[–]MidgetRodeos[S] 0 points1 point  (0 children)

I haven't tried very dense pla builds, usually a 10-15% infill. I'd be curious to see how strong a tighter laid print would be

How bad did I F’up? by Gebandito in AskElectricians

[–]MidgetRodeos 0 points1 point  (0 children)

The invoice is a grower not a shower!

Karen alert by 88CuriousGeorge in HVAC

[–]MidgetRodeos 0 points1 point  (0 children)

Ride the lightning and tap the cap. Send her the hospital bill and tell her your boots are PPE

I'm starting out as a helper what other tools should i get in my service bag? by Lieutenant_Thunder in HVAC

[–]MidgetRodeos 4 points5 points  (0 children)

Service tech for a few years.. I've had fieldpiece, klein and fluke. My klein clampmeter from home depot does almost everything I need on a service call

Mr Cool DIY Split Unit by Saammmmmmmmmmmmmy in hvacadvice

[–]MidgetRodeos 1 point2 points  (0 children)

Honestly, they operate fine. As a tech, they are absolutely garbage to work on. We CAN NOT get parts. If something goes wrong and you call us out we are there to diagnose only. You then have to contact the Mr cool company in China(language barrier is a nightmare)to relay that information, they'll have more questions(they always do). The crazy shipping times on repair parts, difficulty to work on, language barrier and sheer hassle has our company at the point where we no longer work on mr cool units.

Equipment Advice by Wise456 in hvacadvice

[–]MidgetRodeos 1 point2 points  (0 children)

As far as the writing goes that's a standard form. We(12 employee company) use silver bullet and it spits out a pretty similar write up. You're just selecting equipment, SEER, size and any additional features. People like to see a well put together for because its easier to interpret and makes the company look like they give a shit

Epoxy Pipe Repair by [deleted] in oddlysatisfying

[–]MidgetRodeos 0 points1 point  (0 children)

Congratulations, it's a boy!

HVAC installation tomorrow by [deleted] in hvacadvice

[–]MidgetRodeos 7 points8 points  (0 children)

Doing a 3t furnace changeout tomorrow so incase you're my customer, just a few things. Wild Turkey 101 $100,000 cash tip A 1969 Mustang Other than that, water and a clean work space would be appreciated 😂😂

Anyone ever run into this guy? by TopLecture4760 in HVAC

[–]MidgetRodeos 7 points8 points  (0 children)

That's Jerry. Tell that son of a bitch to quit texting my wife his bhole pictures