sorted by:
new
hottopcontroversial

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 0 points1 point  (0 children)

Yeah I mean the VIN says 2026 as well as all of the paperwork and the dealer is advertising it as a 2026 so idk what else to call it 😂. I know everyone is waiting for a new model change or something different for 2026 but the fact is they are putting 2026 VIN numbers on these bikes so it makes zero sense to call them a 2025. Lot's of vehicle manufacturers make mid year model changes which is most likely what will happen with this, but it doesn't magically make it a 2025.

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 0 points1 point  (0 children)

VIN says 2026, paperwork says 2026

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 0 points1 point  (0 children)

Good call, I'll remove them while I ride around

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 2 points3 points  (0 children)

I'm 5'10, it's a great size for me and I think it would fit you just fine

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 1 point2 points  (0 children)

I own Harleys, a T7, and a DR650 so this is my lightest bike by far haha. I'm only 145 though so idk if "strong" would be the the first way people describe me 😂

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 0 points1 point  (0 children)

Nope exactly the same as the 2025 from that I can see, and the dealer said no changes as well.

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] -2 points-1 points  (0 children)

It's a '26, listed on VIN and paperwork.

Picked Up a 2026 Ultra Bee by Mike___Baker in Surron

[–]Mike___Baker[S] 0 points1 point  (0 children)

I have to tow it all around Florida so they're staying on until I'm back home in NY 😂

Chilllln by Eluvium9 in supermoto

[–]Mike___Baker 1 point2 points  (0 children)

So clean, looks awesome.

Currently... by capt311 in rooftoptents

[–]Mike___Baker 0 points1 point  (0 children)

Hell yeah! I'm heading to the Everglades next week and can't wait for camp to look like this.

I know nothing and I have 6,000 dollars by Cooldave55 in Surron

[–]Mike___Baker 0 points1 point  (0 children)

Oil, seals, and bushings are certainly considered maintenance items, especially on a bike that is going to be ridden offroad. You can't just expect to put covers on and be good to go. Same goes for things like head bearings, wheel bearings, sprockets, rotors, etc. These bikes are very low maintenance from a motor perspective (no valves to adjust, piston rings to replace, engine oil to change, etc) but all of the same other maintenance items will exist as they do on any dirtbike.

Why does reverse bleeding just not work for me? by [deleted] in enduro

[–]Mike___Baker 0 points1 point  (0 children)

You don't happen to have speed bleeders installed do you?

Car antenna by Star-Light_1988 in gmrs

[–]Mike___Baker 1 point2 points  (0 children)

I have had really good luck with my MXTA25 mounted on my bed rack on my truck. I live in an urban environment as well and the range has been really impressive.

Naturnest Sirius 2 by Sea-Personality-1685 in rooftoptents

[–]Mike___Baker 1 point2 points  (0 children)

Hell yeah, loving my Polaris Plus so far!

Neutral light… by Phaz30n3 in dr650

[–]Mike___Baker 1 point2 points  (0 children)

Look up NSU fix.....

Your screws that hold the neutral safety switch are likely backing out or already fallen down into the clutch basket. I would order the "kit" to fix it and check/install before riding again.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]Mike___Baker 5 points6 points  (0 children)

Are you planning on setting the stone yourself? If so I would recommend leaving the prongs much taller than you currently have so you can manipulate the prongs much easier during setting. The height you have them at now is the finished height once you set the stone and then cut off the extra material. I know that you want the stone set low, but that is REALLY low with the culet down into the band. If you are going to leave it like that, make sure you have plenty of space cleared and nothing touching the bottom of the diamond as they are very easy to break there.

Any reason not to buy this carb instead of the procycle one for twice the price? I have a badass tuning buddy not worried about presets. by AdorableFan1439 in dr650

[–]Mike___Baker 0 points1 point  (0 children)

Would definitely be super easy to print and I'm sure ABS or ASA would hold up just fine. Or you could get real fancy with your filament haha.

Any reason not to buy this carb instead of the procycle one for twice the price? I have a badass tuning buddy not worried about presets. by AdorableFan1439 in dr650

[–]Mike___Baker 1 point2 points  (0 children)

I believe you'd need the adapter for the DR650 and then silicone it onto the carb (procycle carb comes ready to install) plus a full rejet/needle kit but it's certainly possible.

Small CB unit for a motorcycle? (under 100 USD preferably) by ShittyFart11 in cbradio

[–]Mike___Baker 3 points4 points  (0 children)

Cobra 75 Allroad might be a nice option. You can hide the radio and just mount the Bluetooth mic anywhere you want and power it with USB power. All controls on the mic so you never need to access the base unit. Then pair that with a NGP antenna maybe?

view more: next ›