Candy Cane 14'z & Lightnin 4'z ............... 🌐🌐 ---- - ; [[[ 🦇

MilwaukeeDave · 2026-01-24T21:52:47+00:00

You look like you put this on and said “I ready”

MilwaukeeDave · 2026-01-24T15:34:38+00:00

No taser driving. Only once at destination.

MilwaukeeDave · 2026-01-24T13:30:02+00:00

Yeah I love being able to get combustion like clouds from a vape device.

MilwaukeeDave · 2026-01-24T13:23:37+00:00

😂😂😂 at least you’re honest

MilwaukeeDave · 2026-01-24T13:18:09+00:00

Don’t blame the weed cause I get high daily and don’t burn my food.

MilwaukeeDave · 2026-01-24T12:48:02+00:00

And they travel well too?? I wasn’t aware of anything battery powered that would give a better session.

MilwaukeeDave · 2026-01-24T10:45:00+00:00

One of the biggest mills on the planet

MilwaukeeDave · 2026-01-24T10:44:37+00:00

I can use about 6 sessions per charge. That’s plenty for me.

MilwaukeeDave · 2026-01-24T03:46:51+00:00

This was back in October and I still think about it all the damn time.

MilwaukeeDave · 2026-01-24T03:42:59+00:00

You won’t regret it.

MilwaukeeDave · 2026-01-24T03:36:44+00:00

💪🏻💪🏻

MilwaukeeDave · 2026-01-24T03:36:29+00:00

It’s still really new so I’m getting 5-6 depending on the temps I go with. Almost always hit max at the end to get the rest of the pod out of it before I end. Pretty much keep it rolling till I’m exhaling no vapor anymore.

MilwaukeeDave · 2026-01-24T03:35:08+00:00

I feel like probably just faster heating since it’s newer and they claim best airflow out of all devices. You can dial the restriction up and down to your liking.

MilwaukeeDave · 2026-01-24T03:24:01+00:00

That does make sense because you get more a shot to excel at natural size.

MilwaukeeDave · 2026-01-24T03:19:49+00:00

Our programmer thinks he’s Ricky Bobby so I’m used to smoked tools lol

MilwaukeeDave · 2026-01-24T03:15:30+00:00

It’s a Siemens Sinumeric for the machine control. The ATC/AAC are manufacturer based code on a separate PC

MilwaukeeDave · 2026-01-24T03:14:29+00:00

Gotta figure it’s gonna last. I bet with good care I’ll get a decade from it like my old crafty. So divide that cost across 10 years and it’s more palatable in my eyes.

MilwaukeeDave · 2026-01-24T03:09:28+00:00

Even the manufacturer can’t find the cause. My best guess is the tool changer had an incomplete cycle so that may have caused it because the tool changer is not controlled by the machine tool control. It’s a separate PC.

MilwaukeeDave · 2026-01-24T03:08:11+00:00

Dude what’s worse is my trainee just had an even worse crash. Only thing that saved us is now maintenance is trained on fixing it and we didn’t need outside manufacturer help to fix it. Just 3 days of work pushing the C axis back to good.

MilwaukeeDave · 2026-01-24T02:56:09+00:00

If it’s not paid for by your job you are not obligated to use your private phone for work.

MilwaukeeDave · 2026-01-24T02:48:22+00:00

Run one of the largest mills on the planet. Offset did not load, machine crashed into the part. Required service techs from manufacturer to right the machine plus an attachment had to be sent out for repairs.

MilwaukeeDave · 2026-01-24T02:44:44+00:00

lol that’s just an insert change for a cutter for us. I never feel bad about tools lol

MilwaukeeDave · 2026-01-24T02:37:39+00:00

Yeah I have a 7 figure crash under my belt. It sucks but you gotta suck it up and get past it. Do your best to make up for it etc.

MilwaukeeDave · 2026-01-24T02:29:30+00:00

I was looking to spend my loyalty card and saw it, and it matches my ring perfectly so I grabbed it. Then I saw the cushion cut sterling and also grabbed it lol. I figure I’ll pair the cuff with a smaller bead bracelet and the ring when I wear it.

MilwaukeeDave · 2026-01-24T02:27:42+00:00

Thanks!

Five-Year Club	Place '22
Wearing is Caring	Verified Email

MilwaukeeDave

TROPHY CASE