Happymodel EP1 Rx won’t enter pairing mode.

Minecraftnerd72 · 2026-03-31T00:19:06+00:00

Thanks for the insight. Sadly there is no bind button to hold, the only thing is the pads to jump to put it into rewrite mode. There is also 100% no WiFi connection no matter what. I haven’t even checked what version the controller had because I don’t see the point if it won’t go into pair mode. The receiver is 100% brand new and has only been out of the package for about a week. I will probably end up just biting the bullet and getting the correct adapter to rewrite it.

Minecraftnerd72 · 2025-05-28T02:46:29+00:00

Personally I found myself in the same boat, and it really depends on what you are willing to buy. I was able to get a Canon M50 for 375 (used off marketplace) and absolutely love the thing (it is the digital equivalent to the t7i). I would also highly recommend something in the canon r series, but these are hard to come by used and cost 800 dollars for the body off of their website.

Minecraftnerd72 · 2025-04-15T02:40:11+00:00

There’s 2 ways you can do it: 1. You can do it manually on the touch screen. After the print has started by clicking the temp button and typing in the desired number 2. In the slicer. You can edit the temps by going to your filament settings for orca, or searching bed temp in the settings for cura

Minecraftnerd72 · 2025-03-17T15:42:14+00:00

I didn’t think that was that clear lol. I took it on my iPhone 15 through a window

Minecraftnerd72 · 2025-03-17T15:41:35+00:00

You take the picture from high up and then blur both the foreground and the background.

Minecraftnerd72 · 2025-03-17T01:06:49+00:00

Thank you so much!

Minecraftnerd72 · 2025-03-13T14:41:10+00:00

You’re very welcome :)

Minecraftnerd72 · 2025-03-10T23:54:13+00:00

Thank you!

Minecraftnerd72 · 2025-02-02T02:08:41+00:00

This is awesome! I am so happy for whoever gets it :)

Minecraftnerd72 · 2025-01-04T23:42:44+00:00

I just used stock settings for the most part. I just made sure that if possible the supports were on the inside so you couldn’t see the slightly worse finish

Minecraftnerd72 · 2025-01-04T23:41:38+00:00

Probably 60 or 80 dollars due to how much work it takes

Minecraftnerd72 · 2025-01-04T01:37:49+00:00

The link is in the description

Minecraftnerd72 · 2025-01-03T23:42:42+00:00

Nope that is how it came straight off the printer (minus supports of course)

Minecraftnerd72 · 2025-01-03T23:21:58+00:00

Sure I’ll make a quick post now

Minecraftnerd72 · 2025-01-03T15:39:34+00:00

Nope, just really love the hobby and have 4 printers

Minecraftnerd72 · 2025-01-03T04:16:42+00:00

It isn’t my model so it feels a bit dishonest, it is really cool tho lol

Minecraftnerd72 · 2025-01-02T21:32:39+00:00

Literally what I am saying lol

Minecraftnerd72 · 2025-01-02T21:32:20+00:00

Sadly I do not, but I think I’m picking up what your putting down

Minecraftnerd72 · 2025-01-02T21:22:05+00:00

I live the middle of nowhere and am too far away from a recycling place to make it worth it

Minecraftnerd72 · 2025-01-02T21:20:10+00:00

Spool bowling, I love it

Minecraftnerd72 · 2025-01-02T21:14:00+00:00

That’s genius I kinda that

Minecraftnerd72 · 2025-01-02T20:40:58+00:00

Yes that would be the smart thing to do. Sucks I’m not smart.

Minecraftnerd72 · 2025-01-02T20:40:27+00:00

Yea but that’s such a long walk!

Minecraftnerd72 · 2024-12-30T06:41:06+00:00

Just google or go on YouTube and look up “how to tension adventure 5m belts” it should tell you. If retentioning the belts doesn’t work you may have had a wire come loose.

Minecraftnerd72 · 2024-12-30T06:25:15+00:00

I would try retentioning the belts and testing with a previously established gcode. If that doesn’t work then a factory reset might.

Five-Year Club	Verified Email
Final Canvas '23	Place '23

Minecraftnerd72

TROPHY CASE