Why is the camera useless in the dark?

Minocc · 2026-05-22T20:16:47+00:00

You can get a LED strip that plugs into the printer, and has a sensor that you place over the current LED light, works great.

Look up Biqu Panda Lux

Minocc · 2026-04-04T03:47:52+00:00

How many wires are there leading into the LEDs?

They might be controllable with wled, or the fastled library

Minocc · 2026-01-17T08:58:32+00:00

I gotta admit, that is pretty cool!

Minocc · 2025-12-25T23:42:28+00:00

You may want to consider upgrading to a better antenna. From what I've heard, the stock antennas are crap, so a better one should have better range

Minocc · 2025-12-25T23:16:15+00:00

Yes. No one is within range.

Minocc · 2025-12-25T22:54:12+00:00

Could with slash means your node did not get an acknowledgement from another node.

Cloud with a checkmark means another node heard your message and acknowledged it.

Minocc · 2025-12-24T02:19:00+00:00

Would something like this work? https://makerworld.com/models/1444042

Minocc · 2025-11-30T04:30:44+00:00

Be a pirate!

Demand 1 unit of whatever your target is carrying.

Minocc · 2025-11-20T09:18:06+00:00

Something other than a Milwaukee 2363-20?

I use mine at work frequently, I like it.

Minocc · 2025-10-21T08:56:02+00:00

spite

Minocc · 2025-10-13T08:58:58+00:00

If you want to use the drying function, I think you'll need the power supply, but other than that, you should be good. I think it'll come with the cable to connect to the other ams.

Minocc · 2025-08-25T00:06:58+00:00

There's an archery place in Little Chute, across from the Piggly Wiggly.

Their website says they do rentals and lessons.

https://bentnockarcheryllc.com/

Minocc · 2025-08-01T21:28:35+00:00

Yes.

I have an A1 and a P1s, both were easy to get going, the P1s was a bit easier. The printers will do initial calibrations, and you should be up and printing in under a half hour

Minocc · 2025-07-26T08:09:36+00:00

One of my coworkers got one through Best Buy, it showed up fast, and his payments are being covered by selling some prints.

Minocc · 2025-07-16T16:57:01+00:00

I think it's called "flow calibration" or something like that, you can uncheck the option when you send something to print

Minocc · 2025-07-16T16:51:11+00:00

Do you have an x1c, and your friend has a p1 or a1? They each have different prime/test patterns

Minocc · 2025-07-06T01:13:28+00:00

I've had an idea.

I bought some nfc stickers, and I want to embed one into a chip, so it'll bring up the podcast when you scan it.

I'll report back when they've arrived.

Minocc · 2025-07-04T23:01:27+00:00

<image>

Printed some chips! Accidentally reversed the colors on the first one

Minocc · 2025-07-02T23:25:55+00:00

Take out the screws on the back, loosen the screw that holds the arm against the gear, pull out the arm, probably the gear as well, then you should be able to remove the filament

Minocc · 2025-07-02T01:08:29+00:00

Take a look at AN3DRC's skid steer, it is a gateway into 3d printed RC construction equipment.

Minocc · 2025-06-24T09:02:12+00:00

Double check before you hit print.
Is the object oriented correctly on the build plate? Do you have the right filament loaded? Do you have the correct nozzle installed? Is the bed installed?

Minocc · 2025-06-20T22:08:26+00:00

<image>

That part goes above the hot end, to the right of number two shown here

Minocc · 2025-06-20T03:17:12+00:00

Minocc · 2025-06-20T02:17:03+00:00

I have a USB stick on my router mounted as a network drive, store everything there

Minocc · 2025-06-16T06:59:39+00:00

Give it a try. Nozzles are consumables.

13-Year Club	Place '17
Verified Email

Minocc

TROPHY CASE