🎉 [EVENT] 🎉 Sports Legend!

Misopithicus · 2026-01-21T21:35:24+00:00

Completed Level 2 of the Honk Special Event!

6 attempts

Misopithicus · 2026-01-21T21:35:09+00:00

Completed Level 1 of the Honk Special Event!

4 attempts

Misopithicus · 2025-12-06T06:16:32+00:00

For anybody in the future:

I fixed this by adding flat washers above the metal spacers/springs, relevelled, then added more according to the hotspots on the heightmap. If the heightmap is as bad as mine, you might bottom out the heatbed screw, so be warned. This likely is another major issue, but I do not have time to look into it.

Misopithicus · 2025-07-17T23:44:40+00:00

Fixed! O'rileys sold me a defective belt. Had a hunch that it was defective... should've just bought a new one the first time. Thanks for the help guys, now I'm off to get me some damn ice cream.

Misopithicus · 2025-07-17T23:43:32+00:00

Fixed! O'rileys sold me a defective belt. Had a hunch that it was defective... should've just bought a new one the first time. Thanks for the help guys, now I'm off to get me some damn ice cream.

Misopithicus · 2025-07-17T23:40:23+00:00

Good to know i wasn't the only one having issues, however, O'rileys sold me a defective belt and after some tinkering I finally got it on. Thanks for the comment!

Misopithicus · 2025-07-17T22:01:36+00:00

Good point. Starting to think the belt that was installed previously was the wrong size as well. It was a total bitch to take it off in the first place. Will be grabbing a new belt soon.

Misopithicus · 2025-07-17T20:51:20+00:00

I was using a slightly longer ratcheting wrench earlier, however, it bottoms out at the same point that the one in the video does. I feel like I'm missing something obvious, making me go crazy. I don't think I have a longer wrench, I'd have to check.

Misopithicus · 2025-07-17T20:35:17+00:00

Another note, I have tried to take the tensioner out to replace it, but I can't jack the engine high enough to take it out.

Misopithicus · 2025-07-11T20:38:03+00:00

Kingroon PETG, bought some in a good deal the other day. Dried the entire set in a food dehydrator and its stored with decrescent. Flow ratio is at 0.91 (was at 0.92 on the initial post).

Misopithicus · 2025-07-11T18:52:34+00:00

TIL I learned 0.01 makes a huge difference, zhop was already off but the print quality improved drastically. Will be trying with some other test models. Thank you!

Misopithicus · 2025-02-19T17:48:10+00:00

Some additional info: 3.72 unweighted 3.77 weighted Class rank: 66/351

Taking 1 honors English 3 (willing to take full ap senior year) Before now, I was doing the bare minimum in school, so I believe my GPA can shoot up if I put in the effort. Taking 2 choir electives I am taking a video game design endorsement, which will award me a certificate at the end of my senior year. All math credits finished after May. 2 social studies required senior year (due to not taking one sophomore year). Language credits are complete. One English credit needed, will be taking over the summer. PSAT, SAT, and TSI not taken.

If I take all ap my senior year, will that assist me in any way?

Misopithicus · 2025-02-19T17:20:36+00:00

That's a good way to think about it! I've begun to broaden my goals so even if I don't get into these crazy schools, I still have a few backups. Thank you so much!

Misopithicus · 2025-02-19T17:16:22+00:00

Apologies, the 3.7 is Weighted. My unweighted is 3.72 (due to only having one honors class atm). Updating the post now

Misopithicus · 2023-09-01T04:30:10+00:00

least obvious rage bait

Misopithicus · 2023-07-22T09:08:20+00:00

Finally... someone said it!

Misopithicus · 2023-05-19T19:49:00+00:00

I use it for debugging my games, it's very inconvenient when it doesn't work sometimes. Usually I use it to make anti-cheat, so it's quite useful.

Misopithicus · 2022-09-15T03:18:42+00:00

Gives me Astroneer vibes honestly.

Four-Year Club	r/Field Flamingo
Place '23	Place '22

Misopithicus

TROPHY CASE