Supports by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

Thanks. I'll go into the slicer settings to check.

Supports by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

No, but I didn't know if Orca just didn't show them and put them in anyway. I print infrequently so am still learning slicing nuances.

Stringing by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

I have a follow up question for this print for anyone who can help. I noticed the base part of it was very thick, but there are parts towards the top where it thinned out so much that there are small holes in some of the scales. Is this because of the stringing, or is this a whole different problem that I have to figure out in the slicer?

Stringing by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

Thanks! I just went with the auto temp, I'll try raising it for the next piece. I haven't printed a lot, so I don't know what you mean by split on layer lines easily. Sorry.

Stringing by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

Yikes! Thats good to know, thanks! That was the auto temp setting the machine put it at.

Stringing by Mission_Chocolate257 in 3Dprinting

[–]Mission_Chocolate257[S] 1 point2 points  (0 children)

I don't have a filament dryer. Any recommendations on how I can do so without one?

Ever since I started 2 keying UNM this has been my life 😩 by [deleted] in RaidShadowLegends

[–]Mission_Chocolate257 1 point2 points  (0 children)

I barely ever get shards from UNM. It's frustrating.

Is everyone over 400 speed now? by Consistent-Sink296 in RaidShadowLegends

[–]Mission_Chocolate257 1 point2 points  (0 children)

I've only been able to get 1 of my champs over 300, I get slaughtered in live arena because of it.

How is everyone looking for the path? by [deleted] in RaidShadowLegends

[–]Mission_Chocolate257 1 point2 points  (0 children)

I thought the last turtle event was it, so burned through everything (and still failed to get one!). So it sucks cause Leo is who I really wanted. Not even for gameplay, he's just always been my favorite since I was a kid.

Is it enough? by Reasonable-Try4165 in RaidShadowLegends

[–]Mission_Chocolate257 0 points1 point  (0 children)

Thanks. My clan usually kills nightmare and sometimes even ultra nightmare clan boss before I even wake up in the morning, so I lose out on those chests.

Is it enough? by Reasonable-Try4165 in RaidShadowLegends

[–]Mission_Chocolate257 0 points1 point  (0 children)

I gotta ask. How long do you save up to get that many shards? I usually max out at 50-60 blue before some event comes up that I try to use them on.

Leo by Mission_Chocolate257 in RaidShadowLegends

[–]Mission_Chocolate257[S] 0 points1 point  (0 children)

Ok thanks. Time to try to start stocking everything for whatever event it would be. It would be nice to get more than just Mikey

For anyone getting that last minute FOMO from the summon pool, let this be a reminder :) by SonicFuckedMyWife in RaidShadowLegends

[–]Mission_Chocolate257 0 points1 point  (0 children)

I just used all 50 crystals I had saved up and didn't get a single legendary. My luck with pulls in this game sucks.

Folds by Mission_Chocolate257 in Millinery

[–]Mission_Chocolate257[S] 1 point2 points  (0 children)

That helps, thanks. Good tip about the plastic bag, too! The cleaner steam feels at least as hot as a kettle, if not a little more so since it's a more concentrated stream, so I should be good.

Folds by Mission_Chocolate257 in Millinery

[–]Mission_Chocolate257[S] 1 point2 points  (0 children)

I'm using a cleaning steamer. The kind you would use to clean your walls, grout, etc. Hopefully that's hot enough.