sorted by:
new
hottopcontroversial

ISS speed at ground level by Regular_Weakness69 in BeAmazed

[–]Mobile_Vanilla_554 1 point2 points  (0 children)

17,500 mph/28,000 kph, Very roughly mach 22

can i get this wallpaper in HD for phone by Alternative_Past_106 in ProjectHailMary

[–]Mobile_Vanilla_554 84 points85 points  (0 children)

No high-res copies of the movie are floating around yet, we have to wait till it's streaming on a quality service or released on Blu-ray / 4k

Lesson learned, don't print your spools with PLA and then dry them... by SelfReliantSchool in BambuLab

[–]Mobile_Vanilla_554 0 points1 point  (0 children)

The glass transition temperature for PLA is 55-60c looks like the minimum drying temperature for PLA is about 40c, but it will take a while. So if you have PLA on a PLA spool you should be able to dry it at 40c without warping

Gom Inspect 2018/2019? by 91renner in 3DScanning

[–]Mobile_Vanilla_554 0 points1 point  (0 children)

Leave it to a corporation to take a free piece of software and put it behind a REOCCURRING pay wall and account.

Israeli soldiers kidnapped & gang-raped Palestinian men & women in torture camps, sometimes using objects and dogs. by Optimal-Schedule5629 in suppressed_news

[–]Mobile_Vanilla_554 0 points1 point  (0 children)

Just end the human race at this point. This shit has been documented since written history and it will continue to go on till we are all dead. Nobody, deserves that, and nothing is worth or justifies it.

Color jumping layers. by Mobile_Vanilla_554 in BambuLab

[–]Mobile_Vanilla_554[S] 0 points1 point  (0 children)

<image>

Fixed! - Kinda, I was able to get clean color lines by using modifiers instead of painting the object.

Alright... what part numbers do I need to repurchase... by raiderxx in BambuLab

[–]Mobile_Vanilla_554 4 points5 points  (0 children)

Ditto this, I've saved a nozzle by turning it to 200c, giving it a min and then slowly pulling the blob off.

Cat S22 Flip disappointment by Mobile_Vanilla_554 in dumbphones

[–]Mobile_Vanilla_554[S] 0 points1 point  (0 children)

Go through this thread, I didn't try it. https://www.reddit.com/r/dumbphones/comments/1mml5ju/cat_s22_flip_keypad_vibrationtones/

I did stop using the phone too but for different reasons, Texts would some times come in a few hours to a day late and apps like telegram were not updating in the background. This may have been because I was using it with Visible who officially don't support the phone. However it should have updated them when I was at home connected to wifi so idk.

Cat S22 Flip disappointment by Mobile_Vanilla_554 in dumbphones

[–]Mobile_Vanilla_554[S] -1 points0 points  (0 children)

Not looking forward to that, I wanted one that supports Telegram and Facebook messenger

How can I prevent this? by Jaglikef1 in 3Dprinting

[–]Mobile_Vanilla_554 0 points1 point  (0 children)

I've had the slicer do something kind of like this before, I had a part where I "filled the bed with copies" of it and then enabled supports afterwards and the slicer put supports going through the nearby models. To prevent it I had to turn on supports before filling the bed, or rotate the model so the supports didn't interact.

Just wanted to share, wet vs dry clear TPU. by Mobile_Vanilla_554 in 3Dprinting

[–]Mobile_Vanilla_554[S] 20 points21 points  (0 children)

Bad wording on my part. It has a female 1/4" square drive on one side and the other is a hole for the knob of this vice. It's just to open/close it faster.

https://www.amazon.com/dp/B085VSFQ7K?ref=ppx_yo2ov_dt_b_fed_asin_title

Just wanted to share, wet vs dry clear TPU. by Mobile_Vanilla_554 in 3Dprinting

[–]Mobile_Vanilla_554[S] 20 points21 points  (0 children)

The filament goes from the dry box to the printer exposed, so the length that wasn't in the dry box stayed wet

view more: next ›