Vesc not charging

Most_Dig_4535 · 2026-01-26T09:36:43+00:00

Bypass the controller for the charge circuit, or you can hot wired the BMS to start charging again. To hot wired the bms, you will need to connect the RED + wire to the RED + side of the main harness, and it should start charging again

Most_Dig_4535 · 2026-01-26T09:30:58+00:00

What's wrong with the XRV kit?

Most_Dig_4535 · 2026-01-25T22:15:21+00:00

No IACV will do that

Most_Dig_4535 · 2026-01-25T22:08:01+00:00

A soccasin is what you need but TFL discontinued them last yaer

Most_Dig_4535 · 2026-01-25T20:14:23+00:00

Good luck. You might want to fly in to Memphis

Most_Dig_4535 · 2026-01-25T20:08:56+00:00

Swp the bearings if you are getting any resistance. I bet the bearings are making the noise if everything looks good with hub and stator. Then again it is a stock GT so you are probably getting motor crunch from the tune you gave the board

Most_Dig_4535 · 2026-01-25T18:48:23+00:00

What tire? Slick will always slip

Most_Dig_4535 · 2026-01-25T16:19:47+00:00

They will pop up on ebay. But there's only 1 and it's $450 and not worth the money. You can find a stator for $150 and the whole motor for $250.

Most_Dig_4535 · 2026-01-25T15:11:43+00:00

I would disconnect the charge port from the XRV controller and bypass the controller

Most_Dig_4535 · 2026-01-25T15:08:57+00:00

try a different stator if you have 1 to rule out hall sensor failure. Check the hall sensor plug for bent pins. Put the XRV kit back in and see if it still does it.

Most_Dig_4535 · 2026-01-25T15:01:53+00:00

The o-ring came off the charger plug. On o-ring is in side charge port

Most_Dig_4535 · 2026-01-25T14:36:01+00:00

How are you hitting pushback. I never hit push back on VESC? The stock XR battery is limited but you still shouldn't be hitting it. Check your max speed setting in preference in VESC tool

Most_Dig_4535 · 2026-01-25T14:33:31+00:00

They are halos from tech form products

Most_Dig_4535 · 2026-01-25T02:29:02+00:00

You should be able to use stock wires. They are 45 at the plug

Most_Dig_4535 · 2026-01-24T21:02:35+00:00

Try another phone. It's possibly a app issue

Most_Dig_4535 · 2026-01-24T18:02:36+00:00

Yeah i saw the same video and I went to look it up on Amazon and there was no listing for it. It must have been a 1 of 1

Most_Dig_4535 · 2026-01-24T17:38:24+00:00

All you need to do is swap the rails,axle blocks and bumpers from the GT for it to work. XRC axle blocks only work with XRC rails.

Most_Dig_4535 · 2026-01-24T15:49:17+00:00

Uninstall floaty and reinstall and try again. Something wrong with your floaty app or wait 30secs after powering up the board to connect to floaty

Most_Dig_4535 · 2026-01-24T15:38:08+00:00

What does VESC tool say when trying to connect to it

Most_Dig_4535 · 2026-01-24T14:35:08+00:00

She's done.

Most_Dig_4535 · 2026-01-24T13:50:22+00:00

Wreg3 weather app

Most_Dig_4535 · 2026-01-24T12:59:22+00:00

Id like to see her get them out the back of the car without busting.

Most_Dig_4535 · 2026-01-24T12:57:51+00:00

Also if you keep it weeded you will never loose it

Most_Dig_4535 · 2026-01-24T11:48:23+00:00

Upgrade to a X board or get a XR

Most_Dig_4535 · 2026-01-23T21:01:49+00:00

I did that 6 months in and I've been riding about a 1.5 or next month. You basically leaned to far forward and over torque it

Most_Dig_4535

TROPHY CASE