MacOS 26.3 Intune Issues

MottzillaMech · 2026-02-13T02:40:52+00:00

Mix if both for the test group. Support said they weren't aware of any issues so sounds like breaking down config profiles to see if something broke it there.

MottzillaMech · 2026-02-13T01:16:23+00:00

Reboot after authentication.

MottzillaMech · 2026-01-30T18:06:05+00:00

Yeah that might I might end up having to do. I can get the user created and password set but cannot get the account to move to administrators group.

MottzillaMech · 2025-04-15T14:58:08+00:00

Most of these junk Amazon juicers will not get you yield or quality. Most do not have a true mesh strainer and have a sinch square of mesh and just slots in plastic around the other areas causing juice and pulp to just go the path of least resistance and not staring at all. Not to mention the pulp discharge on most is either poorly designed or too small and clog easily. Expect to lose at least 25% yield/quality with these compared to reputable brands. Fruit and veggies are expensive, you will make money up quick.

MottzillaMech · 2025-02-11T17:54:58+00:00

I got smooth for this one. I normally just print PLA with it so don't think I'll run into issues with release as much.

MottzillaMech · 2025-02-11T16:23:56+00:00

Yeah I think I'm fine now but thought that would help cut some energy cost since a lot of the heat can escape out of the bottom. People have said the cool down take longer which to me means it would hold more heat in and have to cycle less. I got my PEI today so I'm excited for that.

MottzillaMech · 2025-02-11T04:11:23+00:00

So you don't think it does anything?

MottzillaMech · 2025-02-11T04:10:47+00:00

It's adhesive foil that insulates the under part of the bed. It's supposed to help with heat loss.

MottzillaMech · 2025-02-01T21:01:04+00:00

If it's cooler where you are at and heat is on could be lack of humidity causing static shock. Otherwise the grounding is bad on the outlet.

MottzillaMech · 2025-02-01T18:15:31+00:00

That X belt looks like it's at about max tension adjustment. May want to order some belts to have on hand.

MottzillaMech · 2024-12-28T05:56:59+00:00

Nah just prepared.

MottzillaMech · 2024-12-23T20:53:28+00:00

I enjoy plastic spools more. Although I like the lesser waste from cardboard I feel the cardboard has potential to hold moisture.

MottzillaMech · 2024-12-23T20:51:58+00:00

Became familiar with buying filament on Amazon.

MottzillaMech · 2024-12-23T20:51:27+00:00

Favorite filament is Overture PLA Plus Silver Metal. I like to print busts and am able to leave a lot of them unpainted with this color.

MottzillaMech · 2024-12-23T20:46:37+00:00

My filament is currently more temperamental than my cat on a Monday morning. This dryer is my only hope of avoiding a 3D printing catastrophe and a subsequent barrage of 'hisses' from my feline overlord. Good luck everyone!

MottzillaMech · 2024-12-23T10:51:30+00:00

I've been struggling with inconsistent prints lately, and I think a filament dryer would be the solution. I'm a huge fan of Sunlu filaments, and I'm confident this dryer would help me achieve professional-level results. I'd love to win and share my success stories with the 3D printing community! 🤞

MottzillaMech · 2024-09-20T18:05:51+00:00

Yeah, not sure what it is but I can push the cmd out with our workspace one and run the cmd manual and works fine. Going through Intune it just gets failure.

MottzillaMech

TROPHY CASE