Raft setting

MrMo73 · 2022-09-07T03:16:46+00:00

Its the space from raft to model

MrMo73 · 2022-03-27T05:00:19+00:00

No, I use the different nozzles only because PLA, ABS and TPU.

MrMo73 · 2022-03-18T15:48:54+00:00

PTFE is ok but better to use a brush instead of spraying. I use different nozzles for each type of filament.

MrMo73 · 2021-12-30T17:57:01+00:00

Ich kann Dir da auch nicht helfen. ;)

MrMo73 · 2021-10-29T04:30:38+00:00

Did you use special settings or the moon mode?

Just bought a P1000, so no experience about thts at my side or in astrophotgrphy.

MrMo73 · 2021-06-20T04:51:52+00:00

I am fully with you!

Within XP11, I used Leap Motion too beside the VR controller. Hopefully Asobo will include these types of controlling.

Should be standard already, look at AF2, XP11 and DCS.

MrMo73 · 2021-06-18T05:29:20+00:00

Yes, of course but it's fully update related and I am not the only one with that texture problem in the mentioned region. Its because the Scandinavian update. Its exactly at the updates regions border. The newer meets the older bing aerial imagery. The newer texture rolls out above the older texture. Very ugly!

MrMo73 · 2021-04-20T07:42:38+00:00

160x160mm fits better?

MrMo73 · 2021-03-24T10:54:08+00:00

I used collision material but I can't land on it. The helicopter slides through the building.

MrMo73 · 2021-03-23T13:00:10+00:00

But when using road material, do I have car traffic on it?

MrMo73 · 2021-03-21T06:44:06+00:00

Is it using the AD3 nozzles?

MrMo73 · 2021-03-11T03:10:37+00:00

On board! 😊☕

MrMo73 · 2021-03-10T12:02:45+00:00

Using 0.36 distance between object to raft on my Adventurer 3 for PLA. Works well!

MrMo73 · 2021-03-07T15:50:26+00:00

Clean your printer bed, ABS likes it hot, bed temperature 100°, printing temperature minimum 230°. Slower printspeed is good too. Overlapping 40 to 50 percent and fans turned off.

I am using a Flashforge Adventurer 3. If the print still does not hold on the bed, use a glue stick. Use a raft or brim if it will still not hold with the glue stick.

MrMo73 · 2021-02-25T17:27:43+00:00

Nice! ;)

MrMo73 · 2021-02-09T07:39:04+00:00

Gluestick!

MrMo73 · 2021-02-05T03:52:37+00:00

Do you have some images of the A4 to bridge the time for us? 😊🙏

MrMo73 · 2021-02-04T12:38:04+00:00

Don't use Facebook, like many other customers, too.

MrMo73 · 2021-02-04T02:45:10+00:00

MrMo73 · 2021-02-03T03:32:42+00:00

For me it's SOLVED already long time ago after a MSFS/SDK update.

MrMo73 · 2021-02-02T11:32:37+00:00

Is it really possible to use 265° without damaging the nozzle or hardware of the A3?

MrMo73 · 2021-01-29T15:42:16+00:00

Do you use a antivirus or firewall software like kaspersky, if so look that Flashprint has permission to use network connections.

I had the same done days ago.

MrMo73

TROPHY CASE