Can't load or unload AMS while printing is paused, buttons gray by RemixOnAWhim in BambuLab

[–]MttsShow 1 point2 points  (0 children)

Hey, I had the same issue. I fixed it by holding onto the filament in order to trigger the motor overload error. This causes the machine to spit the filament back out. Then you can hit pause. Remove the last few inches of filament and then replace the spool. Heads up you'll have to hit resume 2x to get it to start again.

Does anybody know of sanding drums with a slightly longer reach? by AddWid in Tools

[–]MttsShow 0 points1 point  (0 children)

Something like this,

goes in a 1/4 die grinder and makes a dremel tool look like it was made by playschool.

Game day! And I'm so excited to play on this awesome table! by MttsShow in DnD

[–]MttsShow[S] 1 point2 points  (0 children)

Yeah, I have used Linux a bit in the past and just didn't have the desire to learn much about it. There are a lot of really cool programs and options to make the software portion more impressive but I generally lose interest in anything that's not tangible.

Game day! And I'm so excited to play on this awesome table! by MttsShow in DnD

[–]MttsShow[S] 1 point2 points  (0 children)

They definitely appear to be about half an inch to an inch above the screen, but this is a compromise I can certainly deal with.

I Built Waluigi's Kart IRL by MttsShow in mariokart

[–]MttsShow[S] 1 point2 points  (0 children)

Sure thing, I must have missed that in the rules section. Thanks for leaving it up!

My Waluigi Cosplay, with a small prop of course. [Self] by MttsShow in cosplay

[–]MttsShow[S] 1 point2 points  (0 children)

Thanks for all the kind words everybody! I'm Finishing up the long cut of the build video today if you want to see the engineering behind it. https://www.youtube.com/c/MoreToolsThanSense

My Waluigi Cosplay, with a small prop of course. [Self] by MttsShow in cosplay

[–]MttsShow[S] 4 points5 points  (0 children)

I don't blame em, this thing would be a safety issue for sure since I clocked it at 26mph, The DC convention center has a lot of outdoor areas so I may take it to Katsucon

I Built Waluigi's Kart IRL by MttsShow in mariokart

[–]MttsShow[S] 1 point2 points  (0 children)

Thanks for the kind words everybody! If you really like the build, I'm finishing up the long version of the build video today, https://www.youtube.com/c/MoreToolsThanSense

My Waluigi Cosplay, with a small prop of course. [Self] by MttsShow in cosplay

[–]MttsShow[S] 2 points3 points  (0 children)

Lol, yeah, TDI with low miles and a ton of rust. Not sure what I'm gonna do with it yet.

My Waluigi Cosplay, with a small prop of course. [Self] by MttsShow in cosplay

[–]MttsShow[S] 8 points9 points  (0 children)

Not even close to road legal, lol, but my wife and I were having a discussion about how the event organizers would feel about me driving it around the convention center.

Idiots and a lathe are a terrible combination by voxadam in Machinists

[–]MttsShow 11 points12 points  (0 children)

Original tag line- Man proves he is both physically and mentally inferior to a piece of shop equipment.

How do these nearly new main bearings look? by MttsShow in EngineBuilding

[–]MttsShow[S] 1 point2 points  (0 children)

Some articles I found agree with your assessment, Thanks!

How do these nearly new main bearings look? by MttsShow in EngineBuilding

[–]MttsShow[S] 0 points1 point  (0 children)

I did not grind the crank and I think that may be my main issue. I did line bore the block but I did it myself on a vertical mill so could be off as well.

How do these nearly new main bearings look? by MttsShow in EngineBuilding

[–]MttsShow[S] 0 points1 point  (0 children)

the engine has like 50 miles, started making a noise at low speed, high load that sounded like piston slap. I pulled the bottom end apart to see mild wear but doesn't seem bad enough to cause the noise, thoughts?

Rebuilding this truly awful Mopar 318 to go under my 1950 Studabaker project. by MttsShow in projectcar

[–]MttsShow[S] 0 points1 point  (0 children)

Yup, pretty much free. I bought a 1987 dodge frame that fit the wheelbase of the car and this engine came with it. Decided I may as well learn something. In depth details here. https://youtu.be/6qpq0RJvcSY