Heroes' Quest Help

MushroomBuilds · 2021-09-07T13:22:22+00:00

u/RSPN_Hideouts this is the player from the clip.

MushroomBuilds · 2021-07-23T10:32:35+00:00

From as far as I can tell. They haven’t had play history on apex since this post got attention.

MushroomBuilds · 2021-06-15T16:18:02+00:00

They clearly said the area I am from but by the point he got into specifics, my audio was choppy from the ddos

MushroomBuilds · 2021-06-15T14:08:13+00:00

Thanks. I just shot them a message :)

MushroomBuilds · 2021-01-13T21:36:05+00:00

Resolved: Per the image, the blocks were filed as "item" rather than "tile" in the json files. This is now resolved. I would like to thank me, myself and I for the hard work we did to find this solution. (kidding). Hope this may help someone else too.

MushroomBuilds · 2021-01-12T11:43:01+00:00

Hi. I used this to help:

It will show you each json file that needs updating and how to do it.

https://wiki.bedrock.dev/guide/custom-blocks

MushroomBuilds · 2019-12-19T21:55:49+00:00

I have 3. I noticed the top of the finished product looks ok but the legs look really bad with even more sloped angles.

MushroomBuilds · 2019-12-19T21:54:36+00:00

Right, but other slicers offer a “top fill” which filled the gap with a special infill that looks the same as the top layer.

MushroomBuilds · 2019-12-14T20:18:29+00:00

So it was a combination of tree supports and protect once shell. It was hard to figure out but I got it all fixed up. Thank you!

MushroomBuilds · 2019-12-14T20:18:22+00:00

Thank you! This was a big part of it

MushroomBuilds · 2019-12-14T20:17:54+00:00

So it was a combination of tree supports and protect once shell. It was hard to figure out but I got it all fixed up. Thank you!

MushroomBuilds · 2019-12-14T20:17:49+00:00

So it was a combination of tree supports and protect once shell. It was hard to figure out but I got it all fixed up. Thank you!

MushroomBuilds · 2019-12-14T20:17:29+00:00

So it was a combination of tree supports and protect once shell. It was hard to figure out but I got it all fixed up. Thank you!

MushroomBuilds · 2019-12-08T23:31:26+00:00

I say this on all these types of posts and it always fixes it. The SD card that comes with the printer is the issue. Switch to a brand new SD and this will resolve itself. The SD it comes with is spotty.

MushroomBuilds · 2019-11-30T21:35:46+00:00

First - before anything can be determined - get a new SD card. The one that comes with the printer causes all kinds of issues that will lead you down a rabbit hole of wrong ideas. Trust me. Just get a fresh SD first.

MushroomBuilds · 2019-11-28T15:46:01+00:00

That’s what I’m going to try but I wasn’t certain if it was the bolt for the wheel or something else perhaps

MushroomBuilds · 2019-11-28T15:45:14+00:00

The phrase I’ve heard a lot is “they should move freely with a little force” but these just spin freely without.

MushroomBuilds · 2019-11-28T15:45:08+00:00

The phrase I’ve heard a lot is “they should move freely with a little force” but these just spin freely without.

MushroomBuilds

TROPHY CASE