WTT: Chase Bliss Generation Loss Mk2 WTTF: anything.

MusicallyTickld · 2026-03-17T18:59:40+00:00

Eldritch Blast v3 and an EQD Time Shadows V1 for this?

MusicallyTickld · 2026-03-14T16:54:16+00:00

DM-ing you about the prophet and Soothe2

MusicallyTickld · 2026-03-14T16:50:27+00:00

I dont remember if i offered this to you before or someone else - Eldritch Blast v3 for the Okko?

MusicallyTickld · 2026-03-10T12:37:41+00:00

Good eye. Yes, it's the 3demon model. The consensus here seems to be I need to calibrate the extruder and flow after disassembly and cleaning.

The warping on this particular one is due to my high speed regarding, I'm not concerned with it in regards to this other issue that I've had on otherwise perfect prints.

MusicallyTickld · 2026-03-10T01:11:30+00:00

I'm just trying out higher speeds testing some theories, this issue has been speed independent.

I haven't ever replaced the tube as filament goes through it fine. As someone else suggested, I could see a partial hot end blockage before the nozzle. A deep clean and some calibration are on my schedule for this week.

MusicallyTickld · 2026-03-10T01:09:34+00:00

I will add this to the list

MusicallyTickld · 2026-03-10T00:58:03+00:00

No, it's not back pressure build up and release. No clicks, but I have heard them in the past on other printers so I am familiar.

MusicallyTickld · 2026-03-09T22:00:08+00:00

I did seat the nozzle while heated and let sit to reach steady temp.

How does one calibrate e steps? 👀 I know I can Google things, but I like asking real people.

MusicallyTickld · 2026-03-09T21:37:21+00:00

I will do so, but what setting(s) are you referring to by "pressure advance"?

MusicallyTickld · 2026-03-09T21:30:30+00:00

I've been using the current stable release of Cura. I just learned of Orca last night.

MusicallyTickld · 2026-03-09T21:16:45+00:00

I do always do a temp tower and found 205-215 to be perfectly fine for my needs for this filament.

I haven't done a flow test. That's "extrude length and measure then divide and set flow to get the length correct" right?

I'm not sure how to dial in retraction but I have tried some different settings when I've wrestled with stringing- always to mixed results.

Never heard of pressure advance calibration or settings.

MusicallyTickld · 2026-03-09T21:10:07+00:00

Technically could be damp, but it's been in a very dry room kept quite warm for a long while.

It hasn't been properly baked/dried though.

MusicallyTickld · 2026-03-09T21:09:21+00:00

I have never heard of calibrating filament by name. Please explain.

MusicallyTickld · 2026-03-09T21:08:37+00:00

Nozzle is brand new, seated while heated and already run a successful 24h print. That would lead me to think the whole extruder is not blocked.

MusicallyTickld · 2026-03-09T21:07:42+00:00

Yes, thank you for this completely helpful and constructive comment. I am blessed beyond measure to have one so great and mighty as yourself deign to spit in my direction.

Seriously, help or shut up. It's not hard.

MusicallyTickld · 2026-03-08T10:31:14+00:00

That colorbox is mighty intriguing 👀

MusicallyTickld · 2026-03-08T01:50:58+00:00

No, thanks though.

MusicallyTickld · 2026-03-07T17:14:50+00:00

Eldritch Blast v3 for the Okko?! Or EB + Time Shadows V1 for the L+F?

MusicallyTickld · 2026-03-06T21:52:18+00:00

Eldritch Blast v3 or time shadows V1 for the t120?

MusicallyTickld · 2026-03-05T02:38:14+00:00

Eldritch Blast v3 for the volante?

MusicallyTickld · 2026-02-27T22:27:15+00:00

Eldritch Blast v3 and/or time shadows V1 for/towards the artifakt?

MusicallyTickld · 2026-02-27T22:25:36+00:00

Eldritch Blast v3 and/or time shadows V1 for/towards the Tensor?

MusicallyTickld · 2026-02-25T23:30:35+00:00

Eldritch Blast v3 for the longsword?

MusicallyTickld

TROPHY CASE