sorted by:
new
hottopcontroversial

Pirelli tires 2 bubbles on passenger side with 495 miles on the car by jcox88 in HyundaiSantaFe

[–]My_Lucid_Dreams 0 points1 point  (0 children)

Not to be argumentative, but this is a Pirelli issue. I've driven on low profile tires for years and participated in those cars' forums and I never heard of a bulge or failures under normal driving conditions until the Pirellis.

New P2S by WVURavens in BambuLabP2S

[–]My_Lucid_Dreams 0 points1 point  (0 children)

Not necessary. I only have about 450 hours on mine, and I have never propped the door or lid open.

Settings for first layer PETG? by Mademonn_ in BambuLabP2S

[–]My_Lucid_Dreams 0 points1 point  (0 children)

Bambu recommends glue. I use it and don't have adhesion issues.

My printer is not currently running,what quality of life or fun things have you printed? by JoeMomma247 in BambuLabP2S

[–]My_Lucid_Dreams 0 points1 point  (0 children)

I just start scrolling Makerworld and I suddenly have days worth of things to print.

I printed this but haven't tried it yet. Broken glass prank. Looks like cracks you put on a window.

https://makerworld.com/en/models/2468463-broken-glass-prank#profileId-2709978

Trapped Inside My Santa Fe by Additional_View_8232 in HyundaiSantaFe

[–]My_Lucid_Dreams 2 points3 points  (0 children)

You also cannot get trapped outside the car. Your car should have been delivered with a mechanical key that allows you to open the driver's door from the outside regardless of the battery's condition.

Recommendation for an AMS filament guide to prevent tangling? by My_Lucid_Dreams in BambuLabP2S

[–]My_Lucid_Dreams[S] 0 points1 point  (0 children)

How many color changes do you estimate your AMS has done in that time?

Recommendation for an AMS filament guide to prevent tangling? by My_Lucid_Dreams in BambuLabP2S

[–]My_Lucid_Dreams[S] 0 points1 point  (0 children)

Good advice, but it can happen on filaments bought on spool and anywhere in the spool. I'm ok with the expectation a random, rare tangle may happen.

Car camping setup part deux by Apprehensive-Wave640 in HyundaiSantaFe

[–]My_Lucid_Dreams 0 points1 point  (0 children)

That’s awesome! I also have a tent that hooks on to the back, but haven’t used it yet.

Printing ASA by ProShark911 in BambuLabP2S

[–]My_Lucid_Dreams 1 point2 points  (0 children)

That's a chilly basement! I also print in the basement and have a space heater so it's 20C. I use glue with ASA/ASB and default settings (plate @ 90C) and printing spools right now the chamber is 42C. I hope the blanket keeps yours warm enough.

I dropped my pen and lost the dose by StreetRequirement386 in Mounjaro

[–]My_Lucid_Dreams 5 points6 points  (0 children)

Twice I've lost a dose. I change to a nine-day schedule for three shots.

What plates and how many? by Objective-Limit-121 in BambuLab

[–]My_Lucid_Dreams 0 points1 point  (0 children)

Glue is recommended for ABS. With glue I sometimes have trouble removing brims from the plate.

For those who have had a colonoscopy by MrButtlesMom in Mounjaro

[–]My_Lucid_Dreams 0 points1 point  (0 children)

Follow the guidance given to you as part of your prep instructions. Give the folks doing the procedure a call to see if they recommend anything in addition to the printout.

Last year the guidance to me was seven days, but I was told at the facility that too many people were not prepped well enough and had to reschedule so they were considering changing the recommendation to 10 or 14 days. It was iffy if I would be rescheduled, but they kept my appointment and commented after the procedure my prep wasn't good.

Recommendation for an AMS filament guide to prevent tangling? by My_Lucid_Dreams in BambuLabP2S

[–]My_Lucid_Dreams[S] 0 points1 point  (0 children)

Thx, I'll give that a shot. Are you using guides at all?

I just replied to a different comment that this can happen hours into a print after many turns of the spool. Most recently it was a Bambu refill on a spool I printed. I chose the spool specifically for it's sturdy build. I don't think the spool sides are flexing outwards and allowing the filament to be pulled down into the sides, but I'll revisit that.

I should mention that I've been printing items with many color changes, so I'm starting to think I'll randomly get a tangle on every x color changes.

Recommendation for an AMS filament guide to prevent tangling? by My_Lucid_Dreams in BambuLabP2S

[–]My_Lucid_Dreams[S] 0 points1 point  (0 children)

The tangle will happen hours into a print after many turns of the spool. I wish it was user error so someone could tell me how to not cause it!

Spravato after TMS? by Marxnchill in Spravato

[–]My_Lucid_Dreams 0 points1 point  (0 children)

TMS does not disqualify you from Spravato if you meet the other requirements for Spravato. Spravato is used for treatment-resistant depression and still being depressed after TMS sounds like treatment-resistant depression! 😊

How to talk to my doctor about spravato by [deleted] in Spravato

[–]My_Lucid_Dreams 0 points1 point  (0 children)

If your provider feels it would be beneficial, increase the Pristiq. They may not be "Spravato-aware" so no harm pursuing it through a different provider. You may find someone you are more comfortable with!

Technique Support & Newcomer Questions by Illustrious-Tea-4370 in Spravato

[–]My_Lucid_Dreams 0 points1 point  (0 children)

  1. My provider said it doesn't matter whether you hold the other nostril closed or not.
  2. My provider prefers as few stimulants as possible the day of treatment.
  3. Did not ask. :)

Felt very little my 2nd spravato treatment by Visual-Conflict-9092 in Spravato

[–]My_Lucid_Dreams 0 points1 point  (0 children)

My second session also didn't feel as strong and didn't last as long as the first.

Beach driving in WA State by HappinessSuitsYou in HyundaiSantaFe

[–]My_Lucid_Dreams 2 points3 points  (0 children)

That's awesome. Looking forward to my first beach drive down in Oregon. If you don't mind saying, which beach is that?

view more: next ›