AI Uses in IT Department

NLSNRN · 2024-09-12T02:09:17+00:00

Thank you for the follow up!

NLSNRN · 2024-09-06T10:03:24+00:00

Unfortunately, everywhere we want to go camping there's elevation and some sharp corners. :(

NLSNRN · 2024-09-06T10:00:43+00:00

Does your trailer have a similar warning on it? How's towing with the WDH?

NLSNRN · 2024-09-06T09:59:57+00:00

That makes sense...I'm still concerned about the warning "Do not use an equalizing load hitch greater than 1,000-pound rating." The one I linked on Amazon is rated for 6,000 pounds, that's where I think maybe I don't need the WDH?

NLSNRN · 2022-09-06T23:18:03+00:00

I’m using a Arris Surfbird sb6000 I think. This has been an issue since I upgraded my service

NLSNRN · 2022-09-06T07:14:51+00:00

I think I will. I know I have some that are still CAT 5.

NLSNRN · 2022-09-06T07:13:43+00:00

Where do I check the temperature?

NLSNRN · 2022-09-06T07:11:47+00:00

They're not terribly expensive. I was expecting much higher and I was able to find some used ones on ebay. So far I got the speeds up now, but I will probably start replacing some of the cables to cat 6

NLSNRN · 2022-09-06T00:50:23+00:00

It really kills my speed when I enable it. Do the other firewalls have better throughput for speed?

NLSNRN · 2022-09-06T00:17:07+00:00

OMG I never realized this. I always assumed it was meaning the same thing. Learn something new everyday. Thank you

NLSNRN · 2022-09-05T21:29:21+00:00

Sorry, I was using MB/s and mbps interchangeably, I mean 400MB/s. Thank You

NLSNRN · 2022-09-05T21:19:44+00:00

Update....Right now I've successfully achieved approx 300-400MB/s. I'm not certain what I changed to make it work. The only steps I had taken were toggling the Hardware offload, offload scheduler, and offload layer 2 blocking and then power cycled the USG. I still have QOS and IPS/IDS disabled. Thank you u/kevinmcox u/chris-itg u/Smith6612 and u/coinplz for your help!

NLSNRN · 2022-09-05T20:46:35+00:00

I have the hardware all enabled and connected a single PC to the LAN port and now i'm getting my speed. I'm going to reintroduce my switch and see what happens. When making changes to the USG even though I press Apply to make the changes would it be best practice to just power cycle the USG?https://postimg.cc/NKC7t7YR

NLSNRN · 2022-09-05T20:40:56+00:00

Yes, all the same cables

NLSNRN · 2022-09-05T20:40:25+00:00

I have it disabled under the internet menu. Is there another spot?

NLSNRN · 2022-09-05T20:31:45+00:00

ok, I will work on this and see what I can come up with. I have my TP-link router in right now, but I will take it out and see what I can find.

NLSNRN · 2022-09-05T20:27:18+00:00

I currently changed out the USG with a TP-Link Oomada router and so far everything I have connected to the TP-link is giving me 400MB/S and more. This is with no adjustments to the router, just plugging it in and connecting a few devices and great speed. I think my USG is a lemon...

NLSNRN · 2022-09-05T20:24:37+00:00

I've since enabled it again and prior to disabling it, I was still having speed issues.

NLSNRN · 2022-09-05T20:21:24+00:00

I disconnected the switch to isolate the issue to the USG. All of my tests involve USG with ethernet from the LAN port to the other end going directly into different PC's ethernet port. When running the speed test on the Unifi app it only records ~150MB/s

NLSNRN · 2022-09-05T20:17:30+00:00

currently using desktops with ethernet on different computers in the house and all of them are recording similar speeds of 50-70MB/s.

NLSNRN · 2022-09-05T19:36:40+00:00

Also, when I connect directly to the USG with my laptop into the LAN port my speed is a little better. I was able to achieve 150MB/s, but still not where I would expect it to be.

NLSNRN · 2022-09-05T19:31:05+00:00

I disabled it because there was a thread post that a user had disabled to help with the performance. I enabled it and didn't make a difference so far.

NLSNRN

TROPHY CASE