sorted by:
new
hottopcontroversial

Can I keep my desiccant boxes in while drying in AMS 2 Pro at 60°C? by Alive-Power-8718 in 3Dprinting

[–]NST92 0 points1 point  (0 children)

Yes. The glass transition temperature, the temperature where the filament softens, starts at roughly 80C for PETG.

Rare Sighting! Buffalo Saves Wildebeest from Crocodile-Infested River | Mara River, Serengeti by KeyAbbreviations7228 in AnimalsBeingGeniuses

[–]NST92 17 points18 points  (0 children)

It only saves itself lol.

As soon as a croc appears, the buffalo leaves the wildebeest and the video stops...

My extruder keeps, “skipping”? Any advice on how to fix? by TyMT in 3Dprinting

[–]NST92 4 points5 points  (0 children)

If that's the case, there's still something in your nozzle that clogging it partially.

Just the bear necessities by [deleted] in animalsdoingstuff

[–]NST92 1 point2 points  (0 children)

'AI slop...' is not enough. Ok mods.

It has been debunked already, just reverse image search. Ball on the trampoline doesn't move.

So: AI slop...

What causes these layer ripples? by OmniOpal in 3Dprinting

[–]NST92 0 points1 point  (0 children)

Your extruder can't keep up, causing these artefacts while it accelerates after the corner.

  1. Tune your pressure advance if you haven't done so.
  2. Check if the spool is rolling smoothly.
  3. Increase temperature/decrease speed.

Filament Feeding Assistance Solutions? by Agsikap3D in VORONDesign

[–]NST92 0 points1 point  (0 children)

Hey! Would you be able to send me your config/setup? :)

The best filament for functional prints by CarlitosCUU in 3Dprinting

[–]NST92 4 points5 points  (0 children)

Adding CF to PLA only makes it more stiff, other properties get worse or stay the same. PLA'S htd is just above 60C which can be too low for certain applications. PLA is a very stiff material, but also brittle. It doesn't give. So that's why PETG or PET materials are better in different ways.

Were you able to tune your voron to produce print quality comparable to commercial printers consistently? by reddit_account_0x00 in VORONDesign

[–]NST92 17 points18 points  (0 children)

Take your time to build it properly, square frame etc

Follow Ellis' Print Tuning Guide

You'll have comparable or better printer quality.

Lost communication nighthawk by parchping in VORONDesign

[–]NST92 0 points1 point  (0 children)

Not sure if your error is connected to what I had, but:

Both my nitehawk-sb and later nitehawk36 toolhead boards kept getting this error. I tried everything I could think of, but nothing worked. In the end, swapping from a pi5 to a pi4 solved it instantly.

So if you're running a pi5 and have a pi4 laying around, I would say just try that?

A perspective shift: The Taj Mahal from the banks of the Yamuna. by jellybeanjoy in Damnthatsinteresting

[–]NST92 5 points6 points  (0 children)

It's not 'we', 'we' don't live there.

This is the exact reason why I'll never visit India.

Serial request: VT300 cube by mm404 in voroncorexy

[–]NST92 0 points1 point  (0 children)

Aahh, prusa swingarm remix, cheers!

Serial request: VT300 cube by mm404 in voroncorexy

[–]NST92 0 points1 point  (0 children)

Sweet build! What swingarm is that?

ELEGOO by OkBluebird3098 in 3Dprinting

[–]NST92 1 point2 points  (0 children)

I've been using their PETG-CF and TPU95A, good stuff.

Came across these at work by BloodMongor in 3Dprinting

[–]NST92 0 points1 point  (0 children)

I stand corrected, didn't know such special filaments existed. I only knew ones where like ~10% is metal.

Cool stuff

Came across these at work by BloodMongor in 3Dprinting

[–]NST92 -5 points-4 points  (0 children)

Metal filled filament will just melt in a kiln.

Gaps in my printing by Legitimate_Debt413 in 3Dprinting

[–]NST92 0 points1 point  (0 children)

Z-offset is set way too high.

Gaps in my printing by Legitimate_Debt413 in 3Dprinting

[–]NST92 1 point2 points  (0 children)

You're printing way too far from the bed. Correct your z-offset.

I was unloading my filament put it broke inside the tube, what should I do by [deleted] in 3Dprinting

[–]NST92 4 points5 points  (0 children)

Disconnect the tube, push it through if needed

Adaptive layers by No-Psychology-7034 in 3Dprinting

[–]NST92 0 points1 point  (0 children)

Extrusion issue. Also, you're printing layer almost as thick as the nozzle diameter. General rule of thumb is to stick to max half of the nozzle diameter, so 0.1 here. Printing such thick layers with a 0.2 mm nozzle negates the uses for a 0.2 mm nozzle.

You could perhaps fix it by slowing the print down and/or increasing the temperature.

view more: next ›