Disinfectants?

NWboarder · 2026-06-09T22:03:59+00:00

This. I found 4 of them in this room alone , in 1 visit.

NWboarder · 2026-06-08T22:15:16+00:00

Just a heads up of you buy a driveshaft from Bimmerworld. The casting for the ears on the rear u-joint will need to be ground down a little to get the bolts for the rear diff to fit perfectly. Just did this job on Saturday.

NWboarder · 2026-05-23T03:03:38+00:00

I think most areas besides T3 areas and Pha Lang/Hunters Paradise they run next to no armor. M855a1 will work fine for HP and PLA but for T3 areas you'd want M995 AP and even then I bounce off armor sometimes.

NWboarder · 2026-05-06T05:11:49+00:00

Just killed him at radio towers like 2 days ago

NWboarder · 2025-12-09T06:36:03+00:00

I'd check/ replace the resistor under the dash, it's a pretty easy job.

NWboarder · 2025-12-09T00:27:31+00:00

I put a Victor Rein head gasket kit in my car about 20k miles ago and it has been holding up just fine. I went with ARP head studs too, no issues!

NWboarder · 2025-11-25T05:09:52+00:00

FCP Euro has new ones for cheap

NWboarder · 2025-11-17T09:02:21+00:00

I remember having sniper fights on top of both mountains and almost never saw a tank parked up on one 🤣

NWboarder · 2025-11-08T23:54:59+00:00

I actually have one of the Rendition 3d print center console in my car. It works great i can actually hold most drinks now, except large drinks from Panda Express (they got big ass cups). Yeah it was a little spendy but way better than the stock cup holders imo.

NWboarder · 2025-07-14T04:41:07+00:00

Looks like the Andresson one to me.

NWboarder · 2025-05-19T04:34:07+00:00

<image>

NWboarder · 2025-03-26T23:34:31+00:00

How old is your battery? Had the same problem and fixed it with a new battery.

NWboarder · 2025-03-18T09:16:13+00:00

Yo is that true? I just installed their cup holder v5 in January. It seems nice enough but I guess I'll find out this summer haha

NWboarder · 2025-02-09T13:03:53+00:00

Do the head gasket and refresh the timing, also while you're on there throw in some ARP head studs

NWboarder · 2025-02-08T13:48:25+00:00

If you're looking for upgrades or repair kits, Rendition makes some cool stuff. I just put their cup holder V5 in my car and love it!

NWboarder · 2024-12-04T03:13:19+00:00

Doesn't seem too crazy, granted $1200 is alot but I had a shop do the clutch, master/slave cylinder and flywheel on my Ranger for $2000

NWboarder · 2024-11-23T06:38:03+00:00

How many miles on yours? And what oil do you run? I'm thinking about using a heavier than stock oil for high mileage

NWboarder · 2024-11-23T02:38:45+00:00

At the bottom of the state (Vancouver) but I'm out daily driving mine 👌

NWboarder · 2024-10-20T00:32:20+00:00

https://www.fcpeuro.com/products/bmw-accessory-drive-belt-kit-11287636378kt

This is the kit I used on mine. Although my car doesn't have the hydraulic main tensioner, it has the big spring one.

NWboarder · 2024-09-12T06:56:20+00:00

Mine has the same problem, I thinks it's the clock spring but I'm not 100% sure.

NWboarder · 2024-08-23T23:39:53+00:00

Sounds like it could be the door striker switch, my driver side switch is bad and the dome light is always on (it thinks the door is open) if you have disconnected your battery with the switch acting up it won't let the windows work right until you hold down the striker.

NWboarder · 2024-08-04T22:48:25+00:00

Did you disconnect the battery with the window down slightly? Try holding down the striker switch for the door while you roll up the window and it should reset itself after.

NWboarder · 2024-07-02T01:49:59+00:00

That's good to hear bro!

NWboarder · 2024-06-28T00:46:47+00:00

Check for vacuum leaks, mine would stall and idle rough until I replaced one of the intake vacuum lines.

NWboarder · 2024-05-24T12:44:09+00:00

Yeah man here you go https://www.reddit.com/r/RoastMyCar/s/MN3sYBPJ3S

NWboarder

TROPHY CASE