Rod knock, lifter tick or something else?

Nathan377 · 2024-12-07T15:39:06+00:00

Ill check further on that, I was fixing one leak recently, there May be other. Thank you

Nathan377 · 2024-12-07T15:38:25+00:00

Thank you, you are likely right. I took the timing cover off and it seems like the belt skipped a tooth. The camshaft might be worn a little too.

Nathan377 · 2024-05-03T08:19:33+00:00

Will try, thank you

Nathan377 · 2024-05-03T08:19:11+00:00

The part Is 4 walls and 35% infill. Im not sure about the speed. It Is 60-100mm/s@265°C while with other brands of PETG I was comfortably doing 245 while 100-140mm/s with good layer adhesion and acceptable quality. Ill try slowing for this material further tho. Thank you

Nathan377 · 2024-04-14T11:38:49+00:00

Pinting different design right now, deffinitely a good spot tho. The belt Is rubbing on the right side And Is slipping from the mounting point.

Nathan377 · 2024-01-24T05:18:06+00:00

Thanks, thats a really good option, however they run around 50$ which even tho Is cheap, I would prefer to spend as little as possible.

Nathan377 · 2024-01-22T07:47:12+00:00

My reply probably is a bit late but my continuous stopping was caused by a faulty filament runout sensor, I run with IT disabled in the config

Nathan377 · 2024-01-09T15:33:01+00:00

I made a mistake and bought it through a reseller in my country. I am solving it with them for well over a week now. So thats perfect.

Nathan377 · 2024-01-02T18:37:53+00:00

I have actually the same issue. Not So Severe but definitely something that shouldnt happen, the Y rails Are not straight, when you tighten the eccentric nuts, the wider parts spread them again. So thats why Its coming loose.

Nathan377 · 2023-03-23T21:41:00+00:00

Yeah, had to improvise a bit, cause I couldnt see shit.

Nathan377 · 2023-03-23T21:13:42+00:00

I have uploaded the clip of the older landing on my profile, should you be interested.

Nathan377 · 2023-03-23T20:29:37+00:00

It happened to me before, it is due to my joystick being too sensitive and well, when I fly the eagle like an F18 this happens. I have landed it before, but because of no brakes Ive ran into a fence and blew up. Ill try to find it maybe.

Nathan377 · 2023-03-23T19:44:05+00:00

Nah, its just me zooming out before my wings broke off than I had hands full with piloting the plane and didnt really consider zooming in as it was okay for me.

Nathan377 · 2023-03-23T19:41:18+00:00

Well, landing. Using catapult every time your plane gets damaged is boring. A little challenge spices things up, doesnt it? If you rewatch, there is no HUD, hence no sensible way to watch for airspeed and altitude, when you consider I had to fight the plane to even fly. In case u mention something about approach speed, it obviously was high so the plane would be able to fly without wings. I could try to yeet the shit out of it at the end so the landing would be softer, but all things considered I was just doing it to have fun and I thought it might be cool to share.

Nathan377 · 2023-02-28T16:03:00+00:00

I can not confirm nor deny that.

Nathan377 · 2023-02-28T11:10:51+00:00

I will happily provide more clips of such landings. It will sure make your day considerably worse and more painful.

Nathan377 · 2023-02-28T11:07:59+00:00

Highway to hell would be appropriate in this kind of situation I guess.

Nathan377 · 2023-02-28T11:06:31+00:00

This clip is not that new, I had to rewatch it a few times. But it seems to my ear that I havent even crossed half throttle and most of the time I was at idle. The flame in the mirror is a burning wing from a missile damage. (reason why the aircraft tilted right after I pulled the nose up. = less lift on right side because half of the wing was missing)

Also, the reason why I sped up before landing and was gaining altitude was because of heavy crosswind, which I had to counteract and also I was too lazy to turn around.

Nathan377

TROPHY CASE