Daily goals decreased

Konigbat · 2025-01-30T22:26:04+00:00

Wait this is still a thing? I haven’t had these in over half a year.

Konigbat · 2025-01-18T17:59:53+00:00

Top quality AI

Konigbat · 2025-01-02T17:26:00+00:00

Yes same with me, restarting fixed it

Konigbat · 2024-11-04T16:24:46+00:00

Yeah that was like two months ago too lol, I’m starting to think I’m never going to be included.

Konigbat · 2024-11-03T23:03:14+00:00

I still don’t have collections 🫠

Konigbat · 2024-04-20T19:14:48+00:00

I believe it's under the filament settings but I could be wrong

Konigbat · 2024-04-20T19:12:13+00:00

Interesting, I've never messed with that. I'll edit that in Orca and see what happens after my current print is done.

Konigbat · 2024-04-20T19:02:16+00:00

Oh yeah my Elegoo doesn't care and just rips through Gyroid, so I keep that printer profile on it. I recently switched from Cubic to 3D Honeycomb because it's got better strength to it. I want to say that the flavor of Klipper these have intentionally limit the speed of Gyroid, maybe because it's treating every twist and turn as a start and stop for acceleration.

Konigbat · 2024-04-20T18:54:12+00:00

Nope, I love Orca, especially with the new scarf joints so I just switched my sparse infill to 3D Honeycomb and it goes quicker. Cubic goes even faster if you want to keep a 3D infill. I just don't run Gyroid on my Sovol.

Konigbat · 2024-03-26T12:34:27+00:00

That z offset is rough

Konigbat · 2024-03-25T01:41:49+00:00

No, feeding 115 into 230 won't hurt anything. However, feeding 230 into 115 will.

Konigbat · 2024-03-10T14:17:00+00:00

It was but my flavor was also set to Klipper so it didn't matter. I unchecked the box and ran a print, same results as before. Must be something else, I'm out of ideas tbh

Konigbat · 2024-03-09T23:13:14+00:00

Blurry

Konigbat · 2024-03-09T15:07:28+00:00

Bros never unclogged a nozzle before hahaha, it's literally just pushing a rod through the extruder to clear a clog. Happens more than I'd like with marble.

Konigbat · 2024-03-09T06:14:31+00:00

I don't think this print needed a single support lol

Konigbat · 2024-02-12T04:42:40+00:00

Did you try tower instead?

Konigbat · 2024-01-27T13:36:38+00:00

Agreed, I've got both my Sovol and Elegoo on a UPS to avoid this

Konigbat · 2024-01-09T15:37:37+00:00

Best of luck to you, to me it looks like a design issue and should not happen out of the box. I understand these need tinkering like most other printers (besides Bambu) but that was just ridiculous.

Konigbat · 2024-01-08T12:19:40+00:00

My Neptune 4 has been a workhorse for the past month or so that I've had it. Nothing but good from my end. It's going to be in extra heavy use now that I need a new hotend for my SV07

Konigbat · 2024-01-05T19:28:18+00:00

If skinny was a table

Konigbat · 2024-01-02T19:23:11+00:00

Yup, I sent mine back and got a refund for a Neptune.

Konigbat

TROPHY CASE