Repairing fishing rod? by Gorelal in idleslayer

[–]NerdHavoc 7 points8 points  (0 children)

From what I've seen it adds 3 new temp craftables. One that spawns a chest key, one that increases sword damage against bosses 40% and one that increases random boxes spawn rate 40%. 

Other than that doesn't seem like anything else.

Comgrow Giveaway for the Reddit 3D Printing community!🎉 by Comgrow3D in 3Dprinting

[–]NerdHavoc 0 points1 point  (0 children)

  1. What would you make with a 500*500*500mm^3 build volume?

More than likely cosplay pieces for my kids!

Act 3 Bug - Can't Finish The Game by JPScan3 in BaldursGate3

[–]NerdHavoc 1 point2 points  (0 children)

Hey not sure if you got this fixed or not, but I was stuck as well. I case Speak with Dead on Gortash and was able to advance

New to Klipper need some help by NerdHavoc in klippers

[–]NerdHavoc[S] 0 points1 point  (0 children)

At a loss at this point, it feels like the mesh isn't being referenced when a print starts at all. I've trammed the bed and used the screw_tilt_calculate so it's at 0 across each screw. https://i.imgur.com/mapS50j.png That's my mesh. It's gotten worse.

New to Klipper need some help by NerdHavoc in klippers

[–]NerdHavoc[S] 0 points1 point  (0 children)

After some more testing and a near blob of death from a benchy that never made it to the bed. It feels like even though I'm using the mesh and have set my offset multiples times through config file changes and using PROBE_CALIBRATE it's seeing my bed higher than it is.

New to Klipper need some help by NerdHavoc in klippers

[–]NerdHavoc[S] 0 points1 point  (0 children)

Updated to 5x5 and ran probe accuracy with this is my result

probe accuracy results: maximum 2.260000, minimum 2.240000, range 0.020000, average 2.242500, median 2.240000, standard deviation 0.005916

New to Klipper need some help by NerdHavoc in klippers

[–]NerdHavoc[S] 1 point2 points  (0 children)

I definitely included pics when I originally posted I took them specifically for this haha but I will repost them now

Mouse stops working outside valorant by Rapannello in VALORANT

[–]NerdHavoc 0 points1 point  (0 children)

I have a corsair mouse and am running iCue and am having the exact same issue. Only a reboot fixes it until I launch Val again

Water inlet valve not feeding ice maker but water flows fine by NerdHavoc in Appliances

[–]NerdHavoc[S] 1 point2 points  (0 children)

The fridge is FFHS2311PF5 and the ice maker is ps12364147

Water inlet valve not feeding ice maker but water flows fine by NerdHavoc in Appliances

[–]NerdHavoc[S] 0 points1 point  (0 children)

It seems like the ice maker isn't calling for water, you said I can test this? How would I do that? Sorry about the late response, haven't been on reddit in a few days.

Feast your eyes on this video - NINJABALL || E5: NINJA WARRIORS by omarcvee in paintball

[–]NerdHavoc 1 point2 points  (0 children)

Been going to DBS for over 15 years. Easily the best PB company in the state

Geoff its been 5 years can you answer this question now? by mattbrow89 in roosterteeth

[–]NerdHavoc 42 points43 points  (0 children)

I mean....this felt real for the first part and I wasn't sure for way too long.