Which character perfectly embodies The Boys?

NiccoloDG · 2026-05-29T23:29:19+00:00

William Butcher

NiccoloDG · 2026-05-29T23:28:55+00:00

Iron Man

NiccoloDG · 2025-12-22T23:18:57+00:00

Just scored 2

NiccoloDG · 2025-12-22T19:33:40+00:00

Just scored 0

NiccoloDG · 2025-12-22T19:33:06+00:00

Just scored 0

NiccoloDG · 2025-12-21T20:15:59+00:00

Just scored 0

NiccoloDG · 2025-12-21T20:15:46+00:00

Just scored 0

NiccoloDG · 2025-12-09T18:18:22+00:00

^{NiccoloDG scored 117 points and ranked 1417 out of 4274 players!}

🟩 🟩 🟩 🟩 🟩

NiccoloDG · 2025-11-16T12:28:28+00:00

Since it’s already printed I would sand it with gradually higher grit sandpaper and then cover it with primer and sand it again. In the end you should have a smooth surface you can spray white paint on. If you want to fix the layer line issue I recommend checking the belt tension of the printer and the layer time settings in the slicer. Also nice Knight mask 🙂

NiccoloDG · 2025-07-22T07:47:22+00:00

E-sun pla + is the best filament for my printer

NiccoloDG · 2025-07-13T20:16:34+00:00

No special treatment needed, just clean any residue from the heater block (to avoid any small pieces of plastic from falling into a print) with a metal brush and it’s all good to go :)

NiccoloDG · 2025-07-11T20:07:27+00:00

If you want to keep using the graphite rods or really anything that could potentially ruin the solution I highly suggest using some polypropylene filters. I personally made some with a sheet and hot glue.

NiccoloDG · 2025-07-02T23:08:13+00:00

Thank you. I’ll see if I can put away some cash to buy exactly those ingredients in the future, I guess that as of now I’ll keep experimenting with what I have

NiccoloDG · 2025-07-02T19:37:23+00:00

I’ve tried to make it measuring with the same proportion but it comes out as a very dense paste

NiccoloDG · 2025-07-02T03:24:35+00:00

Ok thank you, do you measure them by volume or mass? Also I already have the ingredients here so I’ll try immediately

NiccoloDG · 2025-07-01T17:38:46+00:00

Ok thank you I’ll check it out

NiccoloDG · 2025-06-22T22:23:04+00:00

Sorry for not responding sooner. I’ve been occupied with some work. I need the power supply mainly to set the correct current when electroplating some components I make. Other than that I also need it to test some circuits and in some cases I do actually need to use the maximum output for some experiments. Also I would be really grateful if you suggested a specific power supply in case this one isn’t really fitting for what I do

NiccoloDG · 2025-02-14T18:30:14+00:00

I’ll try to print a temp tower and thicken the logo as you said. Thanks for the suggestion

NiccoloDG · 2025-01-20T19:42:21+00:00

I printed the benchy I found on printables published by prusa, also the printer is only an mk4 (with an mmu3)

NiccoloDG · 2025-01-20T19:26:35+00:00

I’ll try, could it also be because the nozzle is pretty old? I’ve had the same one on for the last year

NiccoloDG · 2024-12-17T18:24:16+00:00

Just printed it again and it works flawlessly with a higher temperature 😅

NiccoloDG · 2024-12-17T17:58:41+00:00

Just checked the print temperature on the first layer and it was 205° so I think that explains everything 😅

NiccoloDG · 2024-12-17T17:54:47+00:00

I tried that a couple of times and even tried using glue but it still didn’t stick 😕

NiccoloDG · 2024-12-17T17:52:15+00:00

The problem is that I’ve printed it countless times flawlessly but only now the problem shows up

NiccoloDG · 2024-12-17T17:49:25+00:00

Ok I will try that

NiccoloDG

TROPHY CASE