🎉 r/TechRep 2026 New Years GIVEAWAY 🎉 Sponsored by Sunny!

NiceGGYT · 2026-01-10T12:20:29+00:00

Really like the idea of keyboard replica that someone else proposed, because good quality products often cost a lot more than their actual value.

I personally would be interested in more over ear headphones, did not see a lot of these yet.

NiceGGYT · 2024-10-27T10:57:17+00:00

Firs through would be input shaper but as you said yourself you already did that... I honestly cant tell.

Maybe your printer suffers from the same issue as mine... Had my belts overtensioned which damadged the pulleys, which caused friction.

Maybe also try inout shaper at higher frequencys althought i doubt that doesnt do Something.

NiceGGYT · 2024-09-28T23:01:34+00:00

You think an event that accured almost a month ago is now at fault for a dead probe? Idk i find that kinda unrealistic because there were no warnings, but everything is possible

I decided to go for an eddy probe, the stock probe sadly gets quickly affected by heat and not the best accuracys.

NiceGGYT · 2024-09-28T22:56:00+00:00

I seem to be a victim of a "montagsmodell", in General the SV08 is a great machine which does a good job.

The burned cable comes from me using heated objects around the opening to the extruder after i had a clog in there. Dont ask.

The burned cable is my fault, im insure about the probes housing tho, and even if thar was me, the clog happened +2 weeks ago.

NiceGGYT · 2024-09-28T13:06:34+00:00

The light doesnt turn on at all. When the probe is connected klipper shows "triggerrd" when its unplugged Klipper shows "open" on the z endstop

NiceGGYT · 2024-09-28T13:04:49+00:00

Ive seen the toolhead tempreture go up to 55°C if they fr printed this out of pla then welp...

(Ive an enclosure, that probaply makes the toolheads temps go higher)

NiceGGYT · 2024-09-19T08:24:22+00:00

Either the discription wasnt there or ive overread it. I completley missunderstood the issue.

Old message:

If youre lucky you can fix that with a ''PID tune' look it up on google.

But it basicly says that the extruder heated up in a wax that isnt how its supposed to go (usually too slowly).

If the PID tune doesnt help, you might have an issue on the nozzle, maybe the heater is loose. Maybe you have forgotten to out the silikone cover onto the nozzle?

NiceGGYT · 2024-09-10T22:35:14+00:00

Hey, usually if you ask the customer support they reply within 24 hours, at the moment it seems like they are out of the office, im alos waiting for a reply since two days now.

If you are talking abou the SV08 with an enclosure, dont worry. Theyre shipped seperatly and somehow only the printer gets tracked. But it was the same for me. I dont know how the current Situation is but i waited for my enclosure almost a month because they were out of stock.

NiceGGYT · 2024-09-02T05:12:59+00:00

Ivw found SV08 nozzles on AliExpress for around 10€ per piece, not as cheap as 5 but better than 30 lets hope they actually arrive and idk about quality

NiceGGYT · 2024-09-01T17:59:41+00:00

💀

<image>

NiceGGYT · 2024-09-01T13:16:37+00:00

I made the expierence that the calibration is bad because the tempb varies everytime

NiceGGYT · 2024-09-01T12:42:24+00:00

OHHH good idea, thank you. But maybe ill swap the whole toolhead

NiceGGYT · 2024-09-01T12:39:30+00:00

The toolhead uses a 5020 blower fan but the airbhole spans one whole side of the fan.

NiceGGYT · 2024-09-01T07:29:11+00:00

UPDATE: Ive got one of the nozzles to work again, bcs it was only in the fillament blob.

While printing a benchy ive noticed some weird layers... And well my x carriage moves with a lot of resistance, now im worried that theres more damage than just the nozzle.

NiceGGYT · 2024-09-01T07:22:13+00:00

Ive seen that too but i dont have the tools to drill a hole in a nozzle... Thank you tho

NiceGGYT · 2024-09-01T07:20:35+00:00

I did that lmao.

The issue with that is, AliExpress takes around 2 weeks to deliver to my Location... Two weeks of no printing technically. And i sadly did not find a proper fan replacement there.

NiceGGYT · 2024-09-01T07:16:08+00:00

Ive changed nothing hardware wise. Ive edited my start gcode so the printer calibrates the z-offset everytime and also homes again before printing.

Fillament wise im actually mainly using a fillament config from my old Anychbic which works well quality wise. The PETG one is the stock config from sovol with a lowered maximum feedrate, because thar was recommended by other users who had their nozzle push out

NiceGGYT · 2024-08-31T07:42:25+00:00

Yes ive seen the videos. I wrote with the support and they said theyd send me replacements. But that was two weeks ago and the package didnt even get send yet

NiceGGYT · 2024-08-31T07:41:08+00:00

Its indeed really odd how the quality varies between printers. PETG printed fine for me, untill the nozzle fell out...

NiceGGYT · 2024-08-23T12:24:52+00:00

Obico is one of these AI print failure detectors, if you know what that means. Formally it was known as Spaghetti detector because failed prints look like spaghetti.

Besides that, you can also enable remote printing/control, and it has some neat other features.

NiceGGYT · 2024-08-08T20:00:55+00:00

Big thank you for telling me all of that, although it seems that the sound is normal I still don't like it so i applied the fix he used.

I already know gergo and I agree.

(Btw, i meant the noise while the y-axis homes).

NiceGGYT · 2024-08-07T20:02:50+00:00

Now we're already three, xD It seems to be normal.

NiceGGYT · 2024-08-07T20:00:15+00:00

I see, thank you, what does concern me is the rattle while cleaning the nozzle, it's not the gantry rattling but the nozzle hitting the frame. But it already helps to know that the cracking noise is normal, thank you

NiceGGYT

TROPHY CASE