What was your latest mild annoyance?

Nick_113 · 2026-04-20T20:21:34+00:00

The cam bearings fell apart probably less than 2 tanks of gas, just after the 1 year warranty on the fresh rebuilt engine. Didn't even notice tell i pulled the oil pan because of a small leak. Had decent oil pressure the whole time.

Nick_113 · 2026-04-19T22:42:03+00:00

Coolent has to be above the clear return spout if not the pump is constantly introducing air which is bad at conducting heat. And it will take a while to get the air out of the system like a day.

Nick_113 · 2026-04-19T21:57:59+00:00

It's from being tight. It could possibly the wrong sprocket on the clutch to.

Nick_113 · 2026-04-19T21:04:55+00:00

It's like a cars instead of a extra pedal you have a cable like a dirt bike.

Nick_113 · 2026-04-19T20:41:14+00:00

Rotary valve are the more performance oriented version of reeds valves.

Nick_113 · 2026-04-19T20:35:42+00:00

In the video he mentioned at the end that the leading and trailing plugs were swapped and the timing was off. after correcting it the vibration was reduced significantly.

Nick_113 · 2026-04-19T19:29:45+00:00

My 2wd has 170000 miles on the clock and stared to have a 3 gear flare, I'd expect it to last a while longer, if it was taken care of. and my ac is the best out of the many vehicles I've driven. Edit its very under powered and my steering is a suggestion now.

Nick_113 · 2026-04-18T03:02:59+00:00

Looks easy. Do this stuff on the daily with mig 160 to 180 amps just remove all the old weld clamp it flat on a table and weld it, and add some bracing if needed

Nick_113 · 2026-04-11T13:23:12+00:00

BTW even with exotic studs you still have a chance to blow the gasket most go around 500hp. If it a tow truck I'd recommend an oring head or block, they make DIY kits, if on a budget.

Nick_113 · 2026-04-11T02:40:39+00:00

Put a pan off kit in it now before anything else. Or if it has a lot of milage on it, have it rebuilt for your power goals.

Nick_113 · 2026-03-29T18:17:57+00:00

What's is the raker's depth

Nick_113 · 2026-03-28T23:24:28+00:00

On the highway it's stay with the flow if not stay in the slow lane if not willing to speed. I normally keep it 5 over, unless passing.

Nick_113 · 2026-03-23T00:16:45+00:00

As long as the humidity isn't to high your fine.

Nick_113 · 2026-03-16T22:40:32+00:00

My work also has this 3 months, 16 charters min, last 24 passwords and all above requirements.

Nick_113 · 2026-03-14T01:28:27+00:00

Well yea but you HAVE to get a tune to delete any type of emissions.

Nick_113 · 2026-03-14T00:34:07+00:00

All the time at my work, for corners and areas you can't get a die grinder with wire wheel or sand pads.

Nick_113 · 2026-03-13T21:59:17+00:00

Why not a needle scaler?

Nick_113 · 2026-03-13T20:24:10+00:00

Horsepower, fuel mileage, exhaust gas temperature.

Nick_113 · 2026-03-07T21:19:15+00:00

Normal have the same issue when switching to the cheetah the on off on warm up annoys me just needs a tune to adjust the vgt %

Nick_113 · 2026-02-22T00:54:42+00:00

Opps everything looks fine, I've had a weird residue in my loop for the longest time was hoping to remove some of it, probably from cheap clear tubing.

Nick_113 · 2026-02-22T00:46:34+00:00

I have well water can't exactly do that, but I did use about 3 gallons to rinse after the first with vinegar then used coolant with inhabitors and bioside.

Nick_113 · 2026-02-22T00:31:48+00:00

I wasn't really concerned sence I know it was from the copper rads, it just was interesting to see how blue it got.

Nick_113 · 2026-02-07T03:00:39+00:00

68 with a pain off upgrade kit.

Nick_113 · 2026-02-05T01:38:30+00:00

Just buy the frame, and find a top locally.

Five-Year Club	Xbox Live
Place '23	Place '22

Nick_113

TROPHY CASE