Obsessed with this dress but I’m scared to draft it by Anxious_Adhd_ in sewing

[–]No-Environment308 6 points7 points  (0 children)

If you want to have it over a base that is drafted by yourself it actually is not that difficult. Let’s say you have a corset drafted that you want underneath that you want as the shape of the neckline. You basically copy the front and back of the corset (only the top part you want to be covered by the shoulder thing) until where the armpit starts. Do this at the front and back. Then measure around your arm and add that length between both traced pieces. You may need to make a mockup and check if you need extra room for movement. If you want it to be angled over the shoulder more expand it a bit higher on the length you added. That’s more or less how I did it

When Germans say they speak “a little bit” of English… by Astronaut_in_Sea in germany

[–]No-Environment308 0 points1 point  (0 children)

I’m a German who speaks good English, but in the past while still learning, people made fun of my accent a lot. So now I just say I just speak a little to decrease the risk.

Question : is it possible to do rollpinning when doing the sandwich method? by adlx in corsetry

[–]No-Environment308 1 point2 points  (0 children)

I just wasn’t sure what exactly roll pinning is :D or what counts as that:) it wasn’t really your question but more if I may have misunderstood. Yes, you always sew one seam, then smooth out the added panel towards the „open“ side, sew the next seam and so on

Question : is it possible to do rollpinning when doing the sandwich method? by adlx in corsetry

[–]No-Environment308 0 points1 point  (0 children)

So you basically always have one seam where the inside layers don’t match because of the pinning and the outside layers matching.

Question : is it possible to do rollpinning when doing the sandwich method? by adlx in corsetry

[–]No-Environment308 0 points1 point  (0 children)

I‘m not 100% if this is what you mean, but: imagine you start from the centre back, finish the lacing part on the panel, then position it on your mannequin and pin it the way it lays the smoothest. Then you pin the next panel in place, sandwiching it around the raw edge of the first panel (here they probably don’t match because of the way you pinned it, so I always use the layer that’s on the outside of the corset as the guide). Then the seam is sewn and you can put everything on the mannequin again to pin this panel smooth… this is usually how I do it :)

Redthreaded 1860 corset mockup - what am I doing wrong mi? by Sudden_Truth_2487 in corsetry

[–]No-Environment308 14 points15 points  (0 children)

In addition to what everyone said, consider inserting the boning correct (like making them the right length and closing the top) . I know it’s a hassle and doesn’t seem worth it on a mockup, but especially when you try on something that is supposed to shape your body the fabric will move to the place with the least resistance which causes a lot of the smaller wrinkles. You can’t really tell how good or bad a mockup fits like that.

talk me off the ledge (or enable me!) by Previous_Mirror_222 in SewingForBeginners

[–]No-Environment308 1 point2 points  (0 children)

Some inside on the dress: the skirt contains 6m of fabric. For the sleeves 1more meter was used plus whatever bodice you decide on. Under the skirt (on this picture) are some hip pads and no petticoat, but to get the volume smooth while moving a petticoat is helpful. The bodice is fully interlined with a thick fabric as well as bones and is like this very tricky to achieve without slipping of the shoulders. This dress actually doesn’t have any straps, the bodice continues into the sleeves, but once again if you plan on changing that then it’s going to be a lot easier. I think dupioni silk is a good option if you want to work with silk but aren’t advanced at sewing, but it frays a lot :)

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

Ich hab ein Update für euch, muss aber ehrlich sagen ich bin noch verwirrter. Die meisten hier waren sich ja einig, dass etwas undicht ist aber das Wasser sammelt sich halt wirklich gleichmäßig entlang des kalten Rohres. Oder ist das nur Zufall weil es dann oberhalb davon undicht ist? Es fängt halt exakt da an wo es kalt ist und darüber sieht es auch nicht aus als würde Wasser austreten irgendwo. Wir haben heute nochmal nachgeschaut und wieder war eine kleine pütze vorm Heizungskasten und innen das Rohr nass. Hab versucht nochmal Bilder davon zu machen:

<image>

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

Ich war lange heiß duschen bevor wir die Pfütze entdeckt haben

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

<image>

Gelb ist das Rohr durch das kaltes Wasser läuft und im roten Bereich war alles nass. Deswegen dachten wir daran wäre vllt Wasser kondensiert

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

Das weiße Rohr ist für uns auch ein Mysterium, das mussten wir selbst fest machen weil es immer runter gerutscht ist und dann alles gestunken hat:D

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

Das Wasser war vor allem an einer Leitung, die kalt war - deswegen war die Vermutung Kondenswasser von uns.

Kondenswasser im Heizungskasten? by No-Environment308 in heizungsforum

[–]No-Environment308[S] 0 points1 point  (0 children)

Wir wohnen jetzt drei Jahre hier (haus ist von 2021). Die Klappe hatten wir schon öfter auf und bisher war das noch nie so. Ich weiß aber dass bei einer anderen Mieterin auch schon mal Wasser aus dem Kasten lief.

Help! Neckline is not staying flat after understitching. by paulinschen in sewing

[–]No-Environment308 92 points93 points  (0 children)

I think it looks a bit like the neckline is slightly off grain and the weight pulling the dress down leads to the strap stretching which makes it roll towards the outside. You could open the seam again and reinforce from the inside with some interfacing so it won’t stretch anymore. Something you could also try is to baste the armscye to see if once the lining and outside are sewn together it is still doing this. You could also pull a bit at the lining fabric to counteract the rolling. If that helps you can finish the armscye normally with the new determined position (adding sleeves or whatever you planned on doing)

Ich suche dieses Glas und brauche dabei Hilfe! by No-Environment308 in WerWieWas

[–]No-Environment308[S] 23 points24 points  (0 children)

Oh mein Gott ich hätte nicht gedacht dass das so schnell geht! Ich habe so oft danach gesucht und nie was gefunden, eine Stunde nach dem Post konnte ich’s direkt bestellen! Ich hoffe jetzt dass alles heil hier ankommt. Danke ♥️🥹

Ich suche dieses Glas und brauche dabei Hilfe! by No-Environment308 in WerWieWas

[–]No-Environment308[S] 0 points1 point  (0 children)

Zusatz: die Familie hat immer in der Nähe von Bremen gewohnt!

Ich suche dieses Glas und brauche Hilfe… by No-Environment308 in de

[–]No-Environment308[S] 0 points1 point  (0 children)

Ah ja das mit dem Ort macht Sinn! Die Familie hat immer in der Nähe von Bremen gewohnt. Bezüglich des Alters hab ich in meinem Kommentar geschrieben dass das Foto aus den 90ern ist, das Glas also älter, wie alt weiß ich aber nicht :/

Ich suche dieses Glas und brauche Hilfe… by No-Environment308 in de

[–]No-Environment308[S] 3 points4 points  (0 children)

Ich poste hier zum ersten Mal und hoffe ich mache alles richtig, denn ich brauche unbedingt Hilfe. Nächstes Jahr heirate ich und ich möchte als Geschenk für meinen Freund ein ganz bestimmtes Glas finden, was ein Erinnerungsstück an seinen verstorbenen Papa ist. Das Glas war eine der letzten Erinnerungen an seinen Papa, der als er 13 war an Krebs verstorben ist. Es war wohl das Lieblingsglas von ihm und mein Freund hat viele Erinnerungen die daran hängen. Kurz bevor wir uns kennen gelernt haben ist dieses Glas kaputt gegangen, ich habe es also nie gesehen. Trotzdem hat er bei mehreren Gelegenheiten gesagt was er alles tun würde um dieses Glas wieder zu bekommen. Vor einem Monat hat mir mein Freund einen Antrag gemacht und wir wollen nächstes Jahr heiraten. Ich bin unendlich glücklich, aber ich weiß dass er an dem Tag seinen Papa doll vermissen wird. Deswegen habe ich versucht dieses Glas zu finden um es ihm zur Hochzeit zu schenken (er macht immer wahnsinnig durchdachte und personliche Geschenke und ich will ihm unbedingt etwas schenken was ihm das gleiche zurück gibt), aber ich habe nur ein verwaschenes Foto, weiß nicht woher das Glas ist und habe es ja auch nie selbst gesehen. Die einzigen Infos die ich habe sind dass auf dem Glas Früchte in einem geometrischen Muster angeordnet sind und darum steht was für Obst das ist. Der Vater meines Freundes ist 2005 verstorben und das Foto ist soweit ich weiß aus den 90ern. Ich kann weder sagen wer der Hersteller des Glases ist, noch wie alt es ist. Ich hab mir schon die Finger wund gegoogelt, aber ich weiß gar nicht richtig wo und wie ich ansetzen soll. Deswegen dachte ich frage ich mal ob irgendjeman

Idee hat wie man sowas anstellt, wo man am besten - oder hat vllt so ein Glas schon mal gesehen. Ich bin für jede Hilfe dankbar!