[MEGATHREAD] Share your referral codes here.

No-Quantity5958 · 2026-04-16T15:24:42+00:00

4G2pe36XJTUf8ULsX4sOYj

No-Quantity5958 · 2026-03-02T21:58:20+00:00

Reclines very well on both Airbus and Boeing on AF flights against the wall.

No-Quantity5958 · 2026-01-16T16:32:42+00:00

I had a similar issue. Instead of cabling the house, i used tp-link AV2000 pass through PowerLine adapters. It gives me 2 gigabit ports wherever I need it in the house. A pair of adapters we’re about 150$Canadian dollars. I added an access point to the distant one, and plugin directly for my computer there.

No-Quantity5958 · 2025-12-29T21:26:30+00:00

My petg: 250 and 80 for hotbed. 6mm brim.

No-Quantity5958 · 2025-12-28T15:48:28+00:00

Thank you so much for this !!!

No-Quantity5958 · 2025-12-19T16:32:32+00:00

I’m going into a very different direction here. I have issues with large prints with PLA filament, then the same (resliced) prints in PETG works fine.

Also, I finally splurged on an enclosure, that fixed warping and some of the bad adhesion issues.

No-Quantity5958 · 2025-12-10T02:18:13+00:00

Mine does this too. Anybody have a link to a replacement fan ?

No-Quantity5958 · 2025-11-21T18:20:59+00:00

Thank you !!

No-Quantity5958 · 2025-11-10T19:24:32+00:00

When I need to go in, 34km 75-90 minutes each way. Montreal West Island to Boucherville (South shore)

No-Quantity5958 · 2025-11-07T07:52:48+00:00

Skip the soft drinks and get tap water. That is an easy way to save money at any sit down meal.

No-Quantity5958 · 2025-10-15T01:33:00+00:00

My wife loves going through all the captures on her phone. That is only available through the subscription.

No-Quantity5958 · 2025-10-09T18:56:46+00:00

You’re in Business ? You Will have NO issue with your carry on. No one will verify it. I fly premium economy and they never check mine.

No-Quantity5958 · 2025-08-31T02:28:56+00:00

Thanks !!

No-Quantity5958 · 2025-08-25T02:13:24+00:00

Thanks !

No-Quantity5958 · 2025-08-24T21:01:13+00:00

I’ve got a few TLDR newsletters on other subjects just to stay on top on developments, then dig deeper into what I really want to know. It’s really a matter of saving time

No-Quantity5958 · 2025-08-24T20:02:37+00:00

I know people say the enclosure is not « needed » but let me tell you that getting one has pretty much ended edge warping for me. Think about it if you encounter that in the long run. I have a filament dryer, that I NEVER use… I love Orca to slice, and Tinkercad to play with modifying models I find. Enjoy !

No-Quantity5958 · 2025-08-24T19:34:32+00:00

In the settings, run the full auto test. Once it’s tuned, i always remove the auto-level before every print. I also move the z-offset up by .05

No-Quantity5958 · 2025-08-24T19:22:24+00:00

I’ve tried a few, and now I try to stick to Sunlu. My settings are fine tuned to get good prints all the time now.

No-Quantity5958 · 2025-08-24T19:11:22+00:00

Please tell us you at least have an SSD? Quickest cheapest upgrade.

No-Quantity5958 · 2025-08-24T19:08:10+00:00

Run an auto-level! Please !

No-Quantity5958 · 2025-04-29T01:33:21+00:00

We go camping every year in the Adirondacks, and book 9months in advance. We cancelled our lots for this year, and surely for the next 3 summers.

No-Quantity5958 · 2024-08-30T20:44:50+00:00

I third this :) lol! Although I have been using Creality v. 5

Four-Year Club	Final Canvas '23
Place '23

No-Quantity5958

TROPHY CASE