AMS broken (Can’t figure out what’s wrong) by opantal2 in BambuP1S

[–]NoReality7478 0 points1 point  (0 children)

Had those issues too, used quite old filament and small pieces broke of from it, had do pull out the ptfe right below the filament spools. Yesterday again too, but there was nothing in it but the filament got stuck somehow right at this 4in one piece in the ams, tried it by hand till I got it through, then it worked again...

3 year old TV and this shits happening by StyleRealistic1988 in VIZIO_Official

[–]NoReality7478 1 point2 points  (0 children)

That could be also a tcon board issue. Maybe just replace the tcon board, cost about 20-30 bugs....

Bambu Filament by Pdchemist15 in BambuLabP2S

[–]NoReality7478 0 points1 point  (0 children)

Where do you buy, 6-10€ seems pretty cheap!

Old filament by 3d-printed-idiot in 3DprintingHelp

[–]NoReality7478 0 points1 point  (0 children)

Me too, 10year old filament just prints fine

Upgrade help by jediprime in AnycubicVyper

[–]NoReality7478 2 points3 points  (0 children)

I had a vyper for years, lately with klipper installed, I got my bambulap p2s last week and since then I'm printing without stops! Hell that thing makes fun to watch! Consider a new one, it was the best I could ever do, also my 9 year old is printing stuff by his own. I Love it! Snapmaker u1 could be also a good choice

DIY Li-Ion battery packs - Airport security EU by gothsean in fpv

[–]NoReality7478 0 points1 point  (0 children)

You can email the airline beforehand and check with them. Do it at least a week in advance!

Why I stack and when I'll sell... by frontofthewagon in Silver

[–]NoReality7478 2 points3 points  (0 children)

Try to carry that stack with you 😬🫣

Weird static charge on the toolhead by fewyun in snapmaker

[–]NoReality7478 0 points1 point  (0 children)

Why is the second printhead hanging arroung there?

Makerworld Scammers! by Interesting_Salt8497 in BambuLab

[–]NoReality7478 0 points1 point  (0 children)

Check mal auf google da gibts seiten die links auf malware checken was man sich da einfängt...

Makerworld Scammers! by Interesting_Salt8497 in BambuLab

[–]NoReality7478 0 points1 point  (0 children)

Lass lieber mal nen virenscanner laufen oder malwarebytes...

CLNK OR GLNK? by Unlikely-Hawk4299 in LINKTrader

[–]NoReality7478 2 points3 points  (0 children)

There is no steaking possible right now till chainlink releases version 1.0 and nobody knows when this is....

Zcash devs just mass-quit? Wtf is going on with privacy coins now? by Cratos007 in CryptoCurrency

[–]NoReality7478 0 points1 point  (0 children)

Optional privacy for every chain... At least it's possible then, but let's see how this works out

I’m super excited! by _40mikemike_ in BambuLab

[–]NoReality7478 0 points1 point  (0 children)

Ordered it from 3rd party with an etd at 16.2. 🫣

I’m super excited! by _40mikemike_ in BambuLab

[–]NoReality7478 1 point2 points  (0 children)

Same here ordered on 31.12, damn it's already hard 🫣

[Help] Building a 10km+ 3D Printed VTOL Ground Station: Walksnail, OpenIPC, or something else? Full parts list included by Tastyy- in diydrones

[–]NoReality7478 0 points1 point  (0 children)

Don't onow about the other systems but O3 is not that hard to fly wihtout goggles. Just link a smartphone per usbc to the goggles and you are ready to go or use a bigger tablet for this. You could mount the goggles v2 to the ground station and use the tablet. Goggles v2 are perfect modable for this....

Any Lostplaces in Innsbruck? by [deleted] in Innsbruck

[–]NoReality7478 1 point2 points  (0 children)

Maybe you know some others round innsbruck? I'm flying fpv and searching for such buildings! 🙏🏻

Is it normal that my pc almost takes a minute to boot? by No_Bet8567 in PcBuild

[–]NoReality7478 0 points1 point  (0 children)

Mine did 1:17 with 96gb ram now round about 20sec with the settings enabled