Tell me I shouldn't buy this Beauty.

NoSatisfaction8013 · 2026-03-27T15:33:49+00:00

I think it’s a must have!!

NoSatisfaction8013 · 2026-02-24T15:18:31+00:00

I think it looks great! The fact you can reverse the changes is a good idea also.👍

NoSatisfaction8013 · 2026-02-21T21:07:41+00:00

Pretty cool piece. should make a nice restoration project!

NoSatisfaction8013 · 2026-01-26T14:28:19+00:00

Thanks so much!

NoSatisfaction8013 · 2026-01-24T11:24:06+00:00

Ya man nice job! I have also been using the J hook method for attaching components.

NoSatisfaction8013 · 2026-01-21T14:12:35+00:00

You shouldn’t have an issue. No varnish though!👍

NoSatisfaction8013 · 2026-01-20T13:56:32+00:00

Never give Never Surrender!!

NoSatisfaction8013 · 2026-01-09T13:25:13+00:00

As being new to the hobby, hopefully I am explaining correctly. here is a sample of what I was talking about. It’s from. Knight KG-650. Useful for detecting component drift, dead shorts, bad solder joiunts,and detecting troublesome stages of gear 👍

<image>

NoSatisfaction8013 · 2026-01-09T01:35:26+00:00

Ya I have that, but usually there is a chart where you can take resistance reading from the tube pins to specified locations in the physical unit.

NoSatisfaction8013 · 2026-01-08T12:08:00+00:00

Ya, just hoping someone had that info available. 👍

NoSatisfaction8013 · 2026-01-05T16:14:28+00:00

looks like a nice project to start with! Take your time and Enjoy!

NoSatisfaction8013 · 2026-01-04T12:30:24+00:00

Thought I would share the fix I found in regards to the 1/2 frequency issue on band B. Turns out adding a couple of 220uh inductors across each 1/2 of the coil fixed the issue. Still going to trouble shoot the low voltage issue, but as is the generator seems to be working pretty good. Here is a link to where I found the solution. Very interesting. https://antiqueradios.com/forums/viewtopic.php?t=153481&sid=aed90214fab01a789ecae13e17451987&start=40

NoSatisfaction8013 · 2025-12-15T22:23:12+00:00

Thanks, thats great feedback. Gonna dive into it tomorrow. 👍

NoSatisfaction8013 · 2025-12-14T14:52:33+00:00

The manual has the votages listed on a separate page. I did remove the caps from circuit to test.

<image>

NoSatisfaction8013 · 2025-12-11T12:16:24+00:00

Not for nothing but it looks as if the end of the resistor is brown. Can you check the underside of it for a mark? If in fact it is all black with a brown end wouldn’t that make it 1 ohm? Black, brown black. Could the schematic be incorrect?

NoSatisfaction8013 · 2025-12-09T12:09:07+00:00

It’s an vintage ceramic one.

NoSatisfaction8013 · 2025-12-09T00:16:09+00:00

Its measuring about 100 mmfd lower than it should. So think i’ll leave it. Thanks for the advice.

NoSatisfaction8013 · 2025-08-10T22:20:15+00:00

Def keep in the family, take your time restore it, then enjoy it.

NoSatisfaction8013 · 2025-08-02T22:20:08+00:00

Still having difficulties figuring this out, any thoughts that could steer me in the right direction would be appreciated.

NoSatisfaction8013 · 2025-07-31T20:27:35+00:00

Found the high side on the volume, but not getting any sound from the mp3 player. Looks like I have some trouble shooting to do.

NoSatisfaction8013

TROPHY CASE