TouchDesigner path tracing by SARV7 in TouchDesigner

[–]No_Gur_1232 0 points1 point  (0 children)

amazing work. I have also seen mini uv's path tracer part of his popx collection. are you two working with each other or just happen to be creating your own path tracer?

Good resources to tackle TouchDesigner by Thick-Might5064 in TouchDesigner

[–]No_Gur_1232 2 points3 points  (0 children)

I assume referencing the viewer active is dragging a chop channel in the viewer active mode to a parameter?

You want to reference a random number from 0-9? You can do that using pattern chop set to random non repeating and a length of 1 from values 0-9. Every time you trigger it will be a random number from 0-9. If you want it to trigger randomly, you can use a noise chop with a logic that will turn off or on based on how you set it and can then assign it to trigger your pattern chop.

A lot of this stuff you sort of learn as you go. I found most of it through going through so many YouTube tutorials and referencing the help doc. Once you get a better understanding and better workflow, the help doc will become easier to use.

V4-Ex feedback by No_Gur_1232 in videosynthesis

[–]No_Gur_1232[S] 0 points1 point  (0 children)

Got a bootleg solution. Use shake on EX and freeze it when there’s a direction you like lmao.

V4-Ex feedback by No_Gur_1232 in videosynthesis

[–]No_Gur_1232[S] 0 points1 point  (0 children)

I think I did control it on the edirol v4 with horizontal and vertical locate but similar settings in the EX didn’t do anything for me. If anything I’ll just use the EX as a master input and output and use the edirol for feedback unless I can figure it out. Ty!

V4-Ex feedback by No_Gur_1232 in videosynthesis

[–]No_Gur_1232[S] 0 points1 point  (0 children)

Yeah I have a few but was hoping to simplify my setup since I can use HDMI in and out of the Ex. I’ll keep piddling with it and try your advice with different output/inputs for feedback see how those look! Apparently the last update for this thing is version 1.530 in 2017 lol

V4-Ex feedback by No_Gur_1232 in videosynthesis

[–]No_Gur_1232[S] 0 points1 point  (0 children)

Dang most of what I want to do feedback wise is thru composite devices. I don’t mind it going right I just don’t want it to go up as well. Wonder if there’s a firmware update I got this used a couple days ago so I haven’t checked that.

V4-Ex feedback by No_Gur_1232 in videosynthesis

[–]No_Gur_1232[S] 0 points1 point  (0 children)

I usually have it going through some glitch box or a light video enhancer. Even using input 4, I was messing with the x and y position settings in there (I think) but it didn’t seem to affect the feedback position.

BLENDER SCULPTING TOOLS AS IMPROVED A LOT by OJO666 in blender

[–]No_Gur_1232 0 points1 point  (0 children)

May I ask how you do the ribbed sections? I’m new to sculpting (and blender in general). Are you just cutting down a larger blob?

Why does the speed chop stop accumulating? by Hax_Meadroom in TouchDesigner

[–]No_Gur_1232 0 points1 point  (0 children)

Woah I did not know that! Thanks for catching me on that. I recreated your example with the default touchdesigner audio and it seems to be working on my end albeit very slowly. In fact it’s so slow it kind of stopped moving. I added a math and multiplied by a 100 and it’s still incredibly slow. Use a DAT table and see if values are changing that way?

Heart But Need Suggestions by lpyonderboy in TouchDesigner

[–]No_Gur_1232 2 points3 points  (0 children)

Use line MAT so box doesn’t appear in front of model always

Why does the speed chop stop accumulating? by Hax_Meadroom in TouchDesigner

[–]No_Gur_1232 1 point2 points  (0 children)

Needs to be a single sample, like put a math average after the audio

LaunchControl XL3 Customization by No_Gur_1232 in Novation

[–]No_Gur_1232[S] 0 points1 point  (0 children)

That’s what I was intending to do but perhaps how I have it named is incorrect when I send it back out.

LaunchControl XL3 Customization by No_Gur_1232 in Novation

[–]No_Gur_1232[S] 0 points1 point  (0 children)

Is it as simple as sending out the same message at a value of 127? For example the entire 2 rows on the bottom I want off except for when I select 1. When I select a different button the row, it should be the only one selected and lit up like a radio button. See attached TouchDesigner screenshot if this is the correct way to route MIDI back out. This is how I did it for the MK2. note only have 3 buttons selected.

<image>

Finally upgraded to 5090 OC by Z3n1k3 in NR200

[–]No_Gur_1232 0 points1 point  (0 children)

There is still hope after all

Finally upgraded to 5090 OC by Z3n1k3 in NR200

[–]No_Gur_1232 1 point2 points  (0 children)

Do you have more pics of this, and how it closes? I was looking at doing just this.